聚甲基丙烯酸甲酯／纳米SiO2复合粒子的制备与表征

采用甲基丙烯酸-3-甲氧基硅丙酯（MPs）对分散于甲基丙烯酸甲酯（MMA）中的纳米SiO2粒子进行偶联改性，得到了表面改性的纳米SiO2单体分散液，用原位悬浮聚合方法制备了不同SiO2含量的PMMA／纳米SiO2复合粒子。通过红外光谱、透射电镜、差示扫描量热分析和热重分析等方法对制备的纳米复合粒子进行了表征，结果表明，纳米SiO2粒子在PMMA中分散良好；MMA可通过与MPS的共聚而有效地接枝到SiO2粒子表面，当SiO2含量为6．6％（质量分数，下同）、MPS用量为0．06g／gSiO2时，其接枝率可达73．8％；同时，纳米SiO2的引入可提高PMMA的耐热性能，当Si02含量为14.7％时，其玻璃化转变温度和最大热分解速率时的温度分别提高了11．8℃和18．8℃。     

过量TiO2助烧剂对Ba0.998La0.002TiO3陶瓷晶粒生长的影响

采用电性能测定和微观结构分析等方法研究了过量TiO2助烧剂对Ba0.998La0.002TiO3陶瓷晶粒生长的影响.结果表明:对于Ba0.998La0.002TiO3陶瓷在有液相参与烧结的晶粒溶解-淀析过程中,晶粒生长的必要条件是不仅要有液相的形成,而且BaTiO3晶粒必须在液相中有一定的溶解度.由于BaTiO3晶粒在Ba6Ti17O40和Ba2TiSi2O8液相中有足够的溶解度,促进了晶粒的生长,同时旌主掺杂离子进入晶格而释放氧,形成半导性的陶瓷,而BaTiO3晶粒不能溶解于Ba2Ti2SiP2O13液相中,抑制了晶粒的生长.     

超临界CO2萃取丁香花蕾的工艺研究及对萃取物的GC—MS分析

本文应用超临界二氧化碳技术 ,研究了丁香花蕾的最佳萃取工艺。结合温度、压力、堆积密度、CO2 流量等因素对丁香花蕾提取物的萃出率的影响 ,采用四因素三水平的正交设计 ,得出丁香花蕾油萃取的最佳工艺条件为 :压力30MPa ,温度 4 5℃ ,CO2 流量 10L/h ,低堆积密度。作者还对萃取出的丁香花蕾油进行了GC—MS成分分析     

亚砜基改性纤维素膜的SO2气体渗透性能研究

分别使用二甲基亚砜浸泡的物理方法及苯基乙烯基亚砜加成的化学方法对纤维素膜进行了改性,并对改性膜的性能进行了测试.结果表明改性后纤维素膜仍为致密结构,SO2的渗透性能及其对N2的分离性能明显提高,其中改性液中添加二甲基亚砜的均相化学加成反应所得的改性膜具有较好的SO2渗透稳定性.     

Effect of dopants on the performance of CuO–CeO2 catalysts in methanol steam reforming

Steam reforming of methanol was carried out over a series of doped CuO–CeO₂ catalysts prepared via the urea–nitrate combustion method. XRD analysis showed that at least part of the dopant cations enter the ceria lattice. The addition of various metal oxide dopants in the catalyst composition affected in a different way the catalytic performance towards H₂ production. Small amounts of oxides of Sm and Zn improved the performance of CuO–CeO₂, while further addition of these oxides caused a decrease in catalyst activity. XPS analysis of Zn- and Sm-doped catalysts showed that increase of dopant loading leads to surface segregation of the dopant and decrease of copper oxide dispersion. The addition of oxides of La, Zr, Mg, Gd, Y or Ca lowered or had no effect on catalytic activity, but led to less CO in the reaction products. Noble-metal modified catalysts had slightly higher activity, but the CO selectivity was also significantly higher.     

纯化水系统中灭菌方法的应用及比较

分别采用二氧化氯溶液和臭氧水溶液对制药厂纯化水系统的贮罐和管道进行灭菌处理,比较灭菌效果和操作过程,最终认定臭氧水溶液灭菌方法在灭菌效率和水资源节约等方面优于二氧化氯溶液,适用于制药厂水系统管路、贮罐的灭菌处理.     

用钛白废酸和废铁屑制备聚合硫酸铁试验研究

利用钛白废酸和废铁屑制备了无机高分子絮凝剂聚合硫酸铁。详细研究了聚合硫酸铁制备过程中各因素对亚铁氧化、三价铁水解和聚合等过程的影响。确定了制备聚合硫酸铁的最佳工艺条件为：(1)氧化过程：pH为1．5，氧化剂与亚铁的物质的量之比为0．3，氧化温度为60℃，氧化时间为3h；(2)聚合过程：硫酸根与全铁的浓度比为1．4，陈化时间为2h。     

用闪锌矿(方铅矿)精矿催化还原软锰矿(大洋锰结核矿)制取硫酸锰

在稀硫酸(或稀盐酸)溶液中，用闪锌矿(或方铅矿)精矿作还原剂，用可溶性铁盐作催化剂，分解软锰矿(或大洋锰结核矿)，同时制取锰盐和锌盐。该工艺具有反应快速、彻底，工艺流程简单等特点，同时省去了软锰矿的还原焙烧和锌(铅)精矿的氧化焙烧，能够大幅度提高锰、锌(铅)矿的浸出率，对原料矿的品级没有严格要求。     

纳米二氧化钛制备方法研究

目前制备纳米二氧化钛粒子的方法很多,在总结归纳的基础上对各种制备方法所具有的特点进行比较,并指出了其优缺点和适用范围以及相关的研究进展.     

Catalysts based in cerium oxide for wet oxidation of acrylic acid in the prevention of environmental risks

Acrylic acid is a refractory compound for the non-catalytic wet oxidation (WO) process and can seriously damage the environment when released in industrial effluents. Oxidation of acrylic acid by catalytic wet oxidation (CWO) was studied in slurry conditions in a high-pressure batch reactor at 200 °C and 15 bar of oxygen partial pressure. Several solid cerium-based catalysts prepared in our laboratory were used (Ag/Ce, Co/Ce, Mn/Ce, CeO, MnO) and evaluated in terms of activity, selectivity and stability. Mn/Ce shows the higher activity in 2 h with 97.7% reduction of total organic carbon (TOC) followed by: MnO(95.5%)>Ag/Ce(85.0%)>Co/Ce(65.1%)>CeO(61.2%). Attempts were also carried out to analyze the influence of different Mn/Ce molar ratios. High percentages of Mn lead to practically total organic carbon concentration (TOC) abatements while low ratios lead to the formation of non-oxidizable compounds. Acrylic acid was readily degraded by all the catalysts pointing out the high importance of using a catalytic process. pH was an indicator of the reaction pathway and acetic acid was found as the major reaction intermediate compound; however it is completely oxidized after 2 h with exception for Co/Ce, CeO and MnO. Carbon adsorption and leaching of metals were poorly found for Mn/Ce indicating high stability. The catalyst microstructure after the reaction was analyzed and formation of whiskers of β-MnO₂ (or less probably MnOOH) were observed at the catalyst surface. Therefore, Mn/Ce revealed to be a promising catalyst for the treatment of effluents containing acrylic acid; nevertheless, its commercialization depends on further research.