Ion implantation effect on atomic structure of deformed Si, Ir, W, Ni and Cu

It has been revealed, that in Ir subjected to severe plastic deformation, an ultrafine grained structure (UFG) is formed (the grain size of 20-30 nm). Practically no defects have been detected within the grains, while, in the case of Ar⁺ implantation, the subgrain structure with characteristic sizes of about 3-5 nm is formed; defects have been detected within subgrains.The subgrain structure was also revealed in UFG Ni and Cu after severe plastic deformation (SPD) (subgrain size of 3-15 nm), but in the latter case the observed boundary region is broader and subgrain is highly disoriented.     

核材料检测仪的研制

在原来只适于检测(射线的苯基塑料闪烁体上涂以ZnS薄层，使之对γ射线也有很高的灵敏度。根据光电转换原理，采用PC为主控，并用单片机作为数据预处理器，通过标准串口通讯，构成硬件冗余模式；另外，将传统的直通道设计成直角形，使之既能检测金属容器，又能识别强放射性物质；同时，在出口端加装了限速／位阻拦装置，从而解决了γ射线-金属双重识别，反辐射屏蔽和防高速闯关等难题，大大提高了检测系统的可靠性。PC的数据库操作和远程通信等功能使得本仪器能满足现代高端应用的要求。实测表明，本仪器灵敏度高，可靠性好。对应于3mg的U^235仪器报警响应时间小于0．6s，而拦截动作响应时间不大于2s。     

阳泉市煤矿采空区地质因素对公路的破坏

介绍了阳泉市煤矿采空区对公路建设所造成的危害，对其上覆岩层变形破坏的地质因素及其破坏机理作了分析，指出应该采取各种措施减少对公路的破坏。     

控制转炉炉壳蠕变变形

转炉采用镁碳砖炉衬后，炉壳温度急剧增加，炉壳的局部区域会发生永久变形。分析认为：炉壳的永久变形是由于蠕变变形引起，而不是塑性变形引起，给出了影响蠕变变形的因素，指出了控制炉壳蠕变变形的策略。     

考虑介质变形和长期导流能力的裂缝性气藏压裂产能模拟研究

在气藏开采过程中，由于孔隙压力的不断降低，使得介质变形而导致渗透率的变化，进而影响井的产量。针对这一问题，提出了各种流体与固体耦合的数值模拟模型。然而，对于裂缝性储层和多相渗流问题，流固耦合模型中许多参数不易获取，且求解难度很大，使得耦合模型存在一定的应用局限性。很少有文献在气井产能模拟时将介质变形和就地的长期导流能力加以综合考虑。文章考虑介质变形引起的天然裂缝渗透率的变化和裂缝导流能力随时间递减的影响，建立了裂缝性气藏压裂后气水两相渗流数学模型，推导出了数值计算模型；本模型易于编程求解，对于研究裂缝性气藏的渗流特征，特别是进行单井压后产能预测具有一定的实用意义。计算表明：不考虑介质变形和导流能力递减所预测的气产量偏高；目前普遍使用的气藏数值模拟软件中，假定渗透率、裂缝导流能力为常数，以致模拟计算结果比实际偏高。     

CBGA组件热变形的2D-Plane42模型有限元分析

本文介绍有限元中的2D-Plane42模型在CBGA组件热变形中的应用，利用有限元的模拟CBGA组件的应变、应力的分布，通过模拟表明有限元法是研究微电子封装中BGA焊点、CBGA组件的可靠性的方法。     

X-Ray Measurement of Residual Stress in Plastic Bonded Explosives

The X-ray diffractive technology was adopted for tentative study of plastic bonded explosive. The datum of some new diffractive peaks in standard PDF cards were added. The effects of strain to interplanar distance and crystal size of the explosive were studied. The results show that grain size of plastic bonded explosive is decreasing with the increasing of the pressure, and the residual stress of the explosive is draw stress.     

低渗透油田套管损坏机理分析及防治措施

在注水开发油田,油水井套管损坏是一种极为普遍的现象,但又各具特点.通过对鄯善油田套管损坏井的自身特点进行统计、归纳,深入分析低渗透砂岩油藏套管变形影响因素和作用机理,提出了套管损坏井的预防及相应治理措施.     

Slip and Twinning in Polycrystalline Alumina (α-Al2O3) Deformed under Hydrostatic Pressure between 600° and 1000°C

The microstructure of polycrystalline alumina deformed under hydrostatic pressure and at low temperature is investigated by transmission electron microscopy. Deformation occurs mainly by prism plane slip and rhombohedral twinning. Introduction of hydrogen leads to a significant decrease in the yield stress. In large grain size alumina deformed with hydrogen, accommodation of twinning involves dislocation reactions in the twin boundary and in the grains rather than by cracking. Prism plane dislocations decompose into basal dislocations by cross slip probably due to a decrease of Peierls stress for basal slip in the presence of hydrogen.     

三峡工程升船机坝段基础特点与施工期形变特征

简要分析了升船机上闸首基础岩体的特点，在施工期随上部建筑物形成的过程中沉降与水平形变随荷载变化的特征。分析认为:基础岩体形变与其受荷特点相吻合，目前建筑物总体安全状态正常，但部分坝段需引起注意，同时为验证设计、指导施工提供了依据。