氟塑料—石墨板式换热器在高温强腐蚀换热工况中的应用

通过氟塑料－石墨板式换热器在化纤生产中高温强腐蚀换热工况中的实际应用，并与常规换热器的使用情况的对比分析，阐述了这种新型换热设备的特点。     

Novel application of radiotracer techniques for corrosion studies of zinc and aluminium in acidic medium

The adsorption of sulphate ions on Zn and Al was studied in 0.5 M NaClO₄ supporting electrolyte at various pH values in the range of pH=2-7 by radiotracer techniques. It was found in both cases that the adsorption of sulphate passes over maximum in the pH range studied.The phenomena observed are interpreted by the assumption that the main component of the overall process is anion adsorption on the protonated oxides/hydroxides formed as a result of corrosion. At low pH values the steady state coverage with respect to these products should be very low owing to their dissolution; consequently the extent of anion adsorption induced must also be very low. At higher pH values where no protonation occurs the adsorption of anions decreases significantly.     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.     

长距离油、气、水混输管道内壁流动腐蚀的研究进展

就近几十年来，多相流管线的流动腐蚀（CO2腐蚀，H2S腐蚀，腐蚀/冲蚀协同作用），腐蚀/冲蚀数学模型和设计准则，腐蚀检测，腐蚀防护与控制技术等方面的研究进展进行了综述。指出了当前研究中所存在的一些问题，就多相流的研究方向提出了相应的建议。     

Indicators for inspection and maintenance planning of concrete structures

Based on an idea introduced by Benjamin and Cornell (1970. Probability, statistics and decision for civil engineers. New York: McGaw Hill) and previous works by the authors it is demonstrated how condition indicators may be formulated for the general purpose of quality control and for assessment and inspection planning in particular. The formulation facilitates quality control based on sampling of indirect information about the condition of the considered components. This allows for a Bayesian formulation of the indicators whereby the experience and expertise of the inspection personnel may be fully utilized and consistently updated as frequentistic information is collected. The approach is illustrated on an example considering a concrete structure subject to corrosion. It is shown how half-cell potential measurements may be utilized to update the probability of excessive repair after 50 years. Furthermore in the same example it is shown how the concept of condition indicators might be applied to develop a cost optimal maintenance strategy composed of preventive and corrective repair measures.     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

12．5×10^4 m3储油罐底板阴极保护方案比选

对国内外储油罐底板内外侧各种阴极保护方法进行了分析对比。重点介绍了茂名分公司12.5×10~4m~3储油罐底板内外侧阴极保护方案:内侧为涂料加铝合金牺牲阳极阴极保护;外侧为涂料加混合金属氢化物网状阳极阴极保护。     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Corrosion protection of iron by polypyrrole coatings electrosynthesised from a surfactant solution

This work is a study of the electropolymerisation of pyrrole onto iron electrodes in the presence of sodium bis(2-ethylhexyl) sulfosuccinate in a wide pH interval. The characterisation of the films was done using electrochemical techniques, SEM/EDX and IR spectroscopy. We show that it is possible to synthesise homogeneous, adherent and very compact films in the pH range between 7 and 12 under potentiodynamic, galvanostatic and potentiostatic conditions without substrate dissolution. The effects of various parameters on electrodeposition were investigated. The new procedure for the electrochemical synthesis of polypyrrole results in improved anticorrosion properties. The inhibition is proposed to be due to the sum of a repulsion of chloride ions because AOT remains entrapped in the polymer matrix and the presence of the iron oxide. Advantages of the use of surfactants in the electropolymerisation solution are discussed.