锰铜基高阻尼合金中锌量的测定──硫氰酸盐萃取分离络合滴定法

基于甲基异丁基甲酮于稀盐酸介质中定量地萃取Ｚｎ￣（２＋）与ＣＮＳ￣－形成的络阴离子。从而达到与共存的锰、镍、铝、铬的完全分离。在有氟化物、硫脲存在时Ｆｅ￣（３＋）、Ｃｎ￣（２＋）和Ａｇ￣＋也不被萃取。有机相中的锌于ＰＨ５．５“六胺”缓冲介质中返萃取回水相，用ＥＤＴＡ滴定。在文中给定的条件下锌的一次被萃取率可达９９％以上，成功地解决了锰铜基高阻尼合金中共存离子对锌量测定的干扰问题。     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

COMPRESSION FATIGUE CRACK GROWTH BEHAVIOUR OF AN ALUMINIUM ALLOY: EFFECT OF OVERLOADING

Abstract— The behaviour of fatigue cracks in an Al-alloy under cyclic compression, either with or without overloads, was studied. For constant-amplitude compressive cycling, a non-catastrophic (saturation) character of the fatigue crack behaviour was confirmed, with the final depth of a crack depending on the applied load level. Single (tensile or compressive) intermittent overloads were shown to re-activate a previously arrested crack while reversed (tensile—compressive or compressive—tensile) ones were also shown to maintain continual fatigue crack extension under otherwise fully compressive cycling.     

LD钢超塑性压缩变形参数与金相组织

通过对ＬＤ（７Ｃｒ７Ｍｏ３Ｖ２Ｓｉ）模具钢起塑性压缩变形后的金相组织观察研究，分析了变形参数、原始组织对变形后金相组织的影响。     

铜线材酸性高速电镀致密光亮锡、锡铜合金

为了寻找低成本、低腐蚀、低污染高速电镀锡、锡铜合金工艺 ,在含光亮剂、柔软剂DL0 1、0 2、0 3的硫酸槽中在不同的电流密度、不同的搅拌速度下 ,在Φ0 .5mm的铜线上电镀Sn和Sn Cu合金镀层。DL0 1、0 2的主要成分是无芳香族的希夫碱 ,DL0 3的主要成分是醇醛缩合物。结果表明 ,在含有DL0 1、0 2、0 3和 35g/LSnSO4 ,137g/LH2 SO4 的镀液中 ,在Jc=10～ 90A/dm2 ,v=16 0～ 314m/min时 ,所得镀层致密、柔软、光亮。在含CuSO4 ·5H2 O 0 .5 ,3.5g/L的硫酸镀槽中 ,在Jc=9,18A/dm2 ,v=16 0m/min时获得了致密、柔软、光亮的Sn (0 .3%～ 0 .6 % )Cu合金镀层。     

Incoloy 800H合金的应用和性能分析

通过对耐热耐蚀合金Incoloy 80 0H的性能分析 ,指出它与普通奥氏体不锈钢相比具有较优的抗氧化性能、耐蚀性和高温蠕变强度。针对催化裂化装置同轴式沉降再生器内部所用Incoloy 80 0H焊件易出现裂纹的问题进行分析 ,认为在施焊过程中由于合金凝固时有低熔点金属或化合物的液态膜残留在晶界区 ,该合金具有高的焊接热裂纹敏感性 ,若焊材选择不当 ,焊丝填充不充分、缺少保护气等将导致晶间裂纹产生。提出了该合金采用TIG焊接防止热裂纹产生的措施。     

半固态ZnAl 27合金及其二次加热组织

研究了半固态ZnAl27合金及其二次加热组织。结果表明，半固态ZnAl27合金基本无宏观偏析，其组织为细小均匀的近球形非枝晶，综合力学性能远远高于常规铸造合金；二次加热后，α相进一步球化，边缘变得光滑圆整，可以满足半固态触变成形的需要。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

Electrical and growth characteristics of Au/Al0.15Ga0.85N:Si structures with various Si incorporations

We have investigated the growth characteristics of n-Al_0.15Ga_0.85N:Si/GaN and the electronic properties of Au/n-Al_0.15Ga_0.85N:Si diode structures grown by metal-organic chemical vapor deposition (MOCVD) with various Si incorporations. The Al_0.15Ga_0.85N:Si layers were grown on undoped GaN/sapphire (0001) epitaxial layers in a horizontal MOCVD reactor at the reduced pressure of 300 torr. The mirrorlike surface, free of defects, such as cracks or hillocks, can be seen in the undoped Al_0.15Ga_0.85N epilayer, which was grown without any intentional flow of SiH₄. However, many cracks are observed in the n-Al_0.15Ga_0.85N:Si, which was grown with Si incorporation above 1.0 nmol/min. While Au/n-Al_0.15Ga_0.85N:Si diodes having low incorporation of Si showed retively good rectifying behavior, the samples having high Si incorporation exhibited leaky current-voltage (I-V) behavior. Particularly, the Au/n-Al_0.15Ga_0.85N:Si structure grown with Si incorporation above 1.0 nmol/min cannot be used for electrical rectification. Both added tunneling components and thermionic emission influence the current transport at the Au/n-Al_0.15Ga_0.85N:Si barrier when Si incorporation becomes higher.     

Si基膜片型气敏传感器微结构单元的热学性能

微结构气敏传感器由于其微型化、低功耗、易阵列化和易批量生产等优点而受到国内外研究者的广泛关注。利用微机电系统（MEMS）加工技术，制备Si基膜片型微结构单元，并分析其热学性能。这种单元工作区温度为-300℃时，加热功率约75mW；并且膜片工作区的热质量很小，温度可以于毫秒量级的时间内，在室温和450℃之间调制。利用这种微结构单元，可以在温度调制方式下，研究气敏薄膜的电学特性和敏感机理。