Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

WAVE INTERACTION WITH PERFORATED CAISSON BREAKWATERS

The reflection coefficient of perforated caissons and the total horizontal forces acting on them were experimentally and numerically analyzed and discussed when wave propagates normally. To consider the viscosity effect of fluid and nonlinear action of waves on structures, the VOF (Volume Of Fluid) method combined with the k-ε turbulence model was used to simulate the interaction between waves and structures. Governing equations were solved with the finite difference method. Through 2D experimental study in the wave flume, the empirical relationship between the reflection coefficient of perforated caissons and the main affecting factors were obtained from the experimental data using the least square method. Also the correlation between the ratio of the total horizontal force acting on perforated caisson and the force acting on solid caisson and the main affecting factors were regressed from the experimental data.     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

脉冲液体射流泵时均值基本方程中的流速系数

运用非恒定的动量方程和时均值计算方法,对脉冲液体射流泵时均值基本方程中的流速系数进行了理论研究,推导出了喉管和喉管进口段流速系数φ2和φ5的计算式。通过与恒定射流的流速系数计算式对比,阐明了脉冲频率是影响φ2和φ5的主要因素,沟通了脉冲射流与恒定射流流速系数之间的关系。     

油井参数对超声透射系数的影响

为了研究油井各参数对超声波透射系数的影响，根据超声波在媒质中的波函数和边界条件，求出了油井中超声波的透射系数。当井液和水泥层的声速和密度增大时，超声波的透射系数也随之增大，但变化幅度不大，特别是水泥层密度对超声波的透射系数影响很小；当岩层的声速增大时，超声波的透射系数会出现一个极大值；岩层密度对超声波的透射系数影响较大，且随岩层密度的增大超声波的透射系数随之降低。     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

甲基叔戊基醚合成反应的热力学分析

利用戊烯与甲醇合成甲基叔戊基醚(TAME)反应的热力学平衡实验数据, 选择不同的混合活度模型,分别计算得到了该反应体系的平衡常数,并与理论计算得到的平衡常数相比较,筛选出了适合该反应体系的活度计算模型.     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。     

减振器在自导系统结构设计中的应用

通过对减振器结构设计的理论分析，建立了减振器的数学模型，同时通过设计的模拟装置对减振效果进行了实测，效果良好。