Passive target detection and tracking from electromagnetic field measurements

This paper presents a novel approach to the localization of moving targets in a complex environment based on the measurement of the perturbations induced by the target presence on an independently‐generated time‐varying electromagnetic field. Field perturbations are measured via a set of sensors deployed over the domain of interest and used to detect and track a possible target by resorting to a particle Bernoulli filter (PBF). To comply with real‐time operation, the PBF works along with an artificial neural network (ANN) model of the environment trained offline via finite elements (FEs). The performance of the proposed algorithm is assessed via simulation experiments.     

Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation

The present study focuses on experimental investigation of through the thickness displacement and strain field in thin adhesive layer in single sided (unsymmetrical) patch repaired CFRP (carbon fiber reinforced polymer) panel under tensile load. Digital image correlation (DIC) technique is employed to acquire the displacement and strain (longitudinal, peel and shear) field. Experimental determination of shear transfer length based on shear strain field obtained from DIC is introduced to estimate the optimum overlap length which is an essential parameter in patch design for the repair of CFRP structures. Further, DIC experiment with magnified optics is performed to get an insight into complex and localized strain field over thin adhesive layer especially at critical zones leading to damage initiation. The failure mechanism, load displacement behavior, damage initiation and propagation are closely monitored using DIC. The influence of patch edge tapering on strain distribution in adhesive layer is also investigated. The DIC successfully captures the global and localized strain field at critical zones over thin adhesive layer and further helps in monitoring the damage based on strain anomalies. Strains are found to have maximum magnitude at the patch overlap edge and the shear strain level in adhesive layer is higher than the peel strain. Normal tapering increases the peel strain and has negligible influence on shear strain level in adhesive layer. The recommended overlap length is found to be consistent with the recommendation in the literature. Whole field strain pattern and the overlap length obtained from experiment are further compared with the finite element analysis results and they appear to be in good coherence.     

智能型电子式变频电动执行器及其应用

针对原有电动执行器只有以低速运行，通过极强的微调才能修正微小偏差这一缺点，提出智能型电动执行器与各种阀体譬合，利用数字化变频技术，改造目前采用模拟技术的电动执行器，使之具有变速运行、动态响应块，调节定位精度高、稳定性好，故障率低、使用寿命长和应用场合广泛的特点。     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

超短波水文自动测报系统的抗干扰方法

介绍集中解决超短波水文自动测报系统抗干扰问题的方法，重点推荐一种空腔窄带滤波器。     

关于我省数字化城市建设的几点思考

通过对国内外数字化城市建设现状的分析 ,结合我省实际情况 ,提出我省建设数字化城市的对策及建设内容和原则 ,强调政府的组织行为 ,发挥社会各界的积极性 ,充分利用现有资源 ,以建设数字化城市门户网站为先导 ,快速启动全省数字化城市建设。     

低插损窄带型10.7MHz压电陶瓷滤波器的研制

介绍了低插损窄带型10.7 MHz压电陶瓷滤波器的一种设计制作方法。结合压电陶瓷能陷模理论,通过对滤波器分割电极设计和制造工艺控制技术的研究,强调了工艺控制的重要性。产品达到日本村田同类产品水平,对国产化窄带型10.7 MHz压电陶瓷滤波器的研发和生产具有十分重要的意义。认为选用高Qm值压电陶瓷材料、分割电极和耦合电容的设计、焊接和点蜡工艺的控制等是研制低插损窄带型10.7 MHz压电陶瓷滤波器的重点。     

一种适合∑-△A／D转换器的FIR数字滤波器

讨论了一种用于∑-△A／D转换器的固定系数半带（half-band）FIR数字滤波器，分析了其线性相位特性和低通滤波特性，给出了频率仿真结果，以及在Cadence设计系统中的电路和版图实现。     

一种基于ECDSA的USB存储设备访问控制方案

文章针对使用USB存储设备造成的内部泄密问题,提出了一种USB存储设备访问控制方案,该方案对用户的身份认证基于安全强度很高的椭圆曲线数字签名算法,同时使用过滤器驱动程序实现了USB存储设备的读写控制,因而此方案具有较好的安全性、实用性和通用性。