变长线扫描选择性激光烧结快速成型工艺的质量和效率优势分析

本文分析变长线扫描选择性激光烧结快速成型工艺对点扫描工艺的质量和效率优势.对二者光学系统结构作分析对比,对焦斑和线束上的功率密度作计算对比.变长线扫描系统采用的扫描方式和聚焦元件使线束宽度小且恒定,线束功率密度与点扫描焦斑的相当.变长线扫描选择性激光烧结快速成型工艺的质量优势是明显的,效率比点扫描工艺提高一倍左右.     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

Numerical simulations of specimen size and mismatch effects in ductile crack growth - Part II: Near-tip stress fields

The effect of ductile crack growth on the near tip stress field in two different specimen geometries has been investigated. For homogeneous specimens it is observed that the peak stress level increases with ductile crack growth. The effect is most pronounced up to about 1 mm of crack growth. For low and intermediate hardening there is a significant effect of specimen size on the stress level. In case of mismatch in yield stress, the simulations show that the increase in stress level in the material with the lower yield stress is of a similar magnitude as is the case for stationary cracks. In case of ductile crack growth deviation from the original crack plane occurs, the highest stresses are still found close to the interface, and not in front of the current crack tip.     

A comparative study of numerical solutions to non-linear discrete crack modelling of concrete beams involving sharp snap-back

Numerical problems are often encountered in modelling crack propagation in concrete beams using non-linear finite element (FE) analysis, especially when sharp snap-back behaviour in load-displacement relations occurs. This paper firstly identifies 16 arc-length control based numerical strategies based on extensive literature review. They are then used to carefully model the structural behaviour of a four-point single notched shear beam using discrete crack modelling approach in which cracks are represented by interface elements with bilinear softening constitutive laws. Based on extensive FE analyses, detailed comparisons of the merits and demerits of these numerical algorithms are then made. The results indicate that the effectiveness and efficiency of different algorithms may vary considerably from one to another, with the local arc-length based procedures in conjunction with tangential stiffness strategy and reversible unloading model being the most robust.     

Learning to Predict Non-Deterministically Generated Strings

In this article we present an algorithm that learns to predict non-deterministically generated strings. The problem of learning to predict non-deterministically generated strings was raised by Dietterich and Michalski (1986). While their objective was to give heuristic techniques that could be used to rapidly and effectively learn to predict a somewhat limited class of strings, our objective is to give an algorithm which, though impractical, is capable of learning to predict a very general class. Our algorithm is meant to provide a general framework within which heuristic techniques can be effectively employed.     

混凝土结构的质量通病——裂缝

从材料、结构构造、施工工艺、地基变形、温湿度变形等方面论述了混凝土裂缝产生的原因 ,提出只有真正了解裂缝产生的原因 ,才能有针对性地采取有效措施 ,确保工程质量     

高层地下室底板混凝土施工的裂缝控制

以德益花园写字公寓楼地下室底板205m厚混凝土的施工工程为例，坚持预防为主的原则，采取了一系列温控技术措施，有效地防止或控制了温度裂缝(收缩裂缝)的产生，确保了混凝土的施工质量。     

简析Ⅲ类PHC管桩的成因及加固补强处理方法

本文主要通过Ⅲ类PHC管桩的形成分析,经过各方论证采用了合适的处理方法,取得了较好的效果。     

浅析露天栈桥改造

结合工程实例，论述了露天栈桥产生裂缝和腐蚀的原因，对栈桥结构进行了评价，提出了加固方案及加固施工中应注意的事项，经使用证明，加固效果良好。