On basic definitions of unified fracture mechanics terminology

The adoption of unified fracture mechanics terminology (UFMT) will promote efficient communication between specialists in different fields of fracture research, harmonization of national and international standards relating to fracture mechanics, and last but not least improvement of the existing methodology for teaching and education in fatigue and fracture. In this paper the definitions of some basic and related terms included in different standards on fracture mechanics terminology are confronted with one another. Alternative definitions of the same terms are offered. By this strategy the author tries to show that the definitions of basic and related terms appropriate for the UFMT should emerge as a consequence of harmonizing a crack model with an actual crack and then both taken together with a fracture model, laboratory test methods, and failure assessment codes.Published in Problemy Prochonsti, No. 1, pp. 17–29, January, 1996.This paper is published as a matter of discussion.     

Measurements of Stress Intensity Factors of an Interface Crack Under Mixed Mode Loading

The optical method of caustics has been utilised to measure both the stress intensity factor for a crack lying along the interface of an aluminium/epoxy bimaterial specimen, and the mode mixity arising from the difference in the elastic properties across the interface. Measurements were carried out by using a novel modification to the method whereby caustics are produced and measured from both sides of the specimen, so compensating automatically for the distortion induced in the specimen due to misaligned loading fixtures. A flat reflective surface across the interface was obtained by adhering a reflective coating to the specimen. Verification that this coating does not affect measurement accuracy was obtained by comparing stress intensity factors measured from coated and uncoated monolithic aluminium specimens where good agreement was found to exist between both measurements.     

角调谐飞秒同步泵浦KTP红外光参量振荡器

用平均输出功率为１．１Ｗ，脉宽为９０ｆｓ的商用再生锁模Ｔｉ：Ｓａｐｐｈｉｒｅ激光器作为泵浦源，用ＫＴＰ作为非线性光学介质，制成一台同步泵浦飞秒光学参量振荡器。其输出调谐范围为１．０４μｍ至１．２６μｍ，平均输出功率在１００ｍｗ左右，脉宽仅约１００ｆｓ。     

Influence of the counter-ion on the effective charge of polyacrylic acid in dilute condition

Osmotic pressure measurements were satisfactorily used to compute the effective charge of poly(acrylic) acid (PAA) at different pHs and with different monovalent and divalent counterions. This experimental method is sensitive to the osmotically active species (polymer and counterions). After correction for the polymer contribution to the total osmotic pressure (solvency and excluded volume), the remaining pressure can be attributed to the polyelectrolyte counterions and processed with Donnan and equation of state in order to compute the effective charge number per polymeric chain (Z^eff). The behavior of Z^eff against the chain concentration and pH was investigated after neutralization of PAA with LiOH, NaOH, and TMAOH. The results clearly indicate that the nature of the monovalent counterion has no effect on Z^eff leading to the conclusion that the interaction between monovalent counterions and the acrylate functionality is purely electrostatic in agreement with conductimetric and potentiometric results reported in the literature. The behavior of Z^eff against the degree of ionization of the polymer and its concentration is also in good agreement with the theoretical expectations of the theory of ionic condensation. Osmotic measurements were also used in order to understand the influence of divalent cations (Mg²⁺, Ca²⁺, Ba²⁺) on Z^eff of the sodium salt of PAA at pH 9 and at different divalent/acrylate molar ratio. All the divalent cations depress Z^eff each of one at different degrees, confirming a specific divalent/polymer interaction. The energy of hydration of cations can explain most of the observed results with divalents.     

几种高强度钢腐蚀疲劳裂纹扩展行为的研究

本文研究了ＧＣ－４，３０ＣｒＭｎＳｉＮｉ２Ａ和３００Ｍ超高强钢的腐蚀疲劳裂纹扩展行为。考虑了环境，热处理制度，应力比和频率对裂纹扩展的影响。研究结果表明：腐蚀环境和热处理制度对疲劳裂纹扩展有显著影响。在侵蚀性环境中随频率降低，裂纹扩展大幅度上升，随应力比提高，环境影响加剧。利用扫描电镜对试样断口形貌进行了分析，并讨论了高强钢的腐蚀疲劳机理。     

13SiMnNiCrMoV钢切口疲劳裂纹萌生门槛值

本文研究在13SiMnNiCrMoV 结构钢中用尖裂纹的应力强度因子来反映三点弯曲缺口试样的疲劳裂纹萌生规律。当 R=0.1,f=100Hz,试样尺寸 B×W×L=12.5×25×117mm 时,缺口名义应力幅的门槛值为Δσ_(th)=3315ρ~(0.352) MPa,0.5mm≤ρ≤5mmΔK_(th)=250ρ~(0.352) MPam~(1/2)门槛值与ρ有关。同时得到缺口裂纹萌生的循环次数 N_i 与名义应力幅Δσ、缺口曲率半径ρ的定量关系是N_i=3.98×10~(22)ρ~(1.62)/Δσ~(4.85),N_i≤10~(5.5)并讨论了(ΔK_1/ρ~(1/2))_(th)与ρ无关的结论。     

公伯峡水电站高压电缆设计几个技术问题分析

结合公伯峡水电站电缆系统设计，对合理选择电缆截面、敷设方式及保护措施等技术问题加以介绍。由于目前电缆设计标准不太完善，因此设计中应结合电站具体情况，合理地选择和提出技术要求。     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

疲劳裂纹的灰色残差预测

借助灰色理论，建立了预测疲劳裂纹扩展的灰色残差预测模型，并应用此模型预测了某不锈钢构件腐蚀疲劳裂纹的扩展，得到了较高精度的预测结果，为疲劳裂纹预测提供了一种简易而可靠的新途径。     

大体积砼产生裂缝的原因及防治措施

大体积砼裂缝问题是建筑业普通关心的问题.对砼裂缝进行控制,就必须研究砼结构中裂缝产生的原因以及在实际的设计和施工过程中采取合理的、经济的措施来控制裂缝.本文通过对大体积砼裂缝成因的理论研究,提出了合理的裂缝控制的设计和施工措施.