省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

轻型钢结构吊车梁设计方法及节点构造

通过分折和研究单层门式刚架轻型钢结构厂房中的吊车梁设计，总结了轻型钢结构吊车梁的设计方法和节点连接构造，对合理设计吊车梁，降低用钢量提出了设计建议。     

冶金厂房钢吊车梁设计中一些问题的探讨

对双层翼缘板焊接工型钢吊车梁的某些受力特征、吊车梁的支座节点连接构造设计等进行了较详尽的分析,提出了满足冶金工业厂房大跨度、大吨位吊车梁系统受力和工艺要求的方法.     

工业厂房48M抽柱工程施工工艺

以莱钢万力H型钢有限公司抽柱换梁工程为例，介绍行车梁拼装、柱加固拆除及托粱吊装前后的测量观测。     

浅谈先张法预应力空心梁板施工质量通病的分析和防治

通过对先张法预应力空心梁板施工时容易忽视和发生的几个质量通病产生原因的分析，并结合工程实际和工作体会，粗略探讨了防治这些质量通病的一些措施和方法。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

High Gd Concentration GaGdN Grown at Low Temperatures

GaGdN layers were grown at temperatures below 300°C by radio-frequency plasma-assisted molecular beam epitaxy on sapphire substrates. GaGdN samples with high Gd concentration as high as 12.5% were obtained by lowering the growth temperature. X-ray diffraction results showed no obvious secondary phase, which means that the phase separation can be suppressed by the growth at low temperatures. All samples, including those grown at room temperature, showed ferromagnetic characteristics. Photoluminescence emission was observed, though spectra exhibit broad and sharp luminescence bands related to many kinds of defects. It is suggested that electrons coming from defects, especially, nitrogen vacancy, stabilize ferromagnetism, and that the carrier-induced ferromagnetism occurs in the low-temperature-growth GaGdN.     

海洋平台双相不锈钢管线的焊接

就双相不锈钢的特异性能．介绍双相不锈钢管线的焊接特点与技术。     

阶梯教室、图书馆的结构设计

结合阶梯大教室的结构布置设计和预应力混凝土技术的运用，阐述该类结构的合理布置和预应力梁设计方法。