井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

烟气轮机叶片应力分析与寿命评估方法评述

烟气轮机是炼油厂催化裂化装置的关键设备,合理预测叶片疲劳寿命是保障烟机安全运行的有效手段。从力学建模和边界条件两个方面简要阐述了叶片的应力分析方法,并系统分析了影响烟机叶片疲劳寿命的主要因素,提出了利用改进的局部应力应变法进行叶片寿命预测的合理性和叶片疲劳寿命的评估方法。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

宽带放大器可靠性问题浅析

叙述了国产高频宽带放大器的质量和可靠性现状，详细介绍了这类产品的质量一致性检验、可靠性摸底试验和现场使用过程中出现的可靠性问题，用统计的方法得出了可靠性特征量，通过对失效样品的失效分析，总结出宽带放大器主要的失效模式和失效机理，并提出了消除和减少失效、提高宽带放大器可靠性的措施和建议。     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

合成氨制气中的以水代汽新工艺

提出了应用油水融合技术在合成氨部分氧化法制气中以水代汽的工艺途径，并分析了其效果和意义。     

利用视电阻率饱和度法分析稠油油藏动用状况

为了弄清稠油油藏蒸汽吞吐井附近油层的动用状况．利用侧钻井视电阻率饱和度分析法，研究电阻减小率与含油饱和度的关系．以确定蒸汽吞吐井附近油层的动用状况。实践证明，该方法切实可行，为调油油田蒸汽吞吐阶段油层动用程度研究，提供了一条新途径。     

管道流体瞬态—水汽锤计算原理

文中介绍了核电站管道中流体瞬态——水汽锤的计算原理;既适用于液体介质的水锤计算,也适用于可压汽体的汽锤计算.对于一些典型管道部件的处理方法,文中也作了讨论。     

烟气轮机特殊状态下的保护

从烟气轮机超速的极限开始 ,分别按照阀门的关闭时间为 1 .5s和 6s的两种典型状态 ,对烟机在联轴节断裂等特殊工况下的超速情况进行了分析。最后 ,对烟气轮机在特殊工况下的保护提出了建议。     

山西甲醇生产应用的调查

在深入调查的基础上阐述了山西省甲醇生产使用的现状和规划，分析了各种不同原料生产甲醇的经济效益，提出了山西省发展甲醇工业的建议。