黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Reaction scheme and kinetic modelling for the MTO process over a SAPO-18 catalyst

A kinetic model for simulation of the MTO process over SAPO-18 catalyst in a wide range of operating conditions has been proposed. The kinetic model predicts the experimental evolution of reaction products with time on stream, which follows three consecutive periods: initiation (where olefin production increases), a period of maximum olefin production and a period in which this production decreases. The kinetic scheme takes into account these three steps that evolve with time on stream: formation of active intermediate compounds, an step where olefins are formed by reaction of oxygenates (methanol/DME) with these intermediates and deactivation of intermediates by degradation to coke. The presence of water in the reaction medium attenuates the reaction rate of these steps. Discrimination of kinetic equations and calculation of the parameters of best fit have been carried out by solving the mass conservation equations of the individual components of the kinetic scheme together with the kinetic equation for deactivation and taking into account the effect of water on the kinetics of each step.     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

PLC和触摸屏在服装熨烫中的应用

由于PC的出现改变了工业控制设计者的设计思想，随着科学技术的发展，服装工业正在变革，而这所有的变革主要集于服装机械的不断革新，它是现代服装工业发展的基础所在。可编程控制器（PLC）和触摸屏（PT）在自动化控制中应用越来越广泛。可编程控制器（PLC）的使用可对提高控制系统的可靠性控制精度。增强系统的抗干扰能力等起到重要作用。而触摸屏的使用则为整个控制系统提供了良好的人机操作界面．因此二者的有机结合越来越广泛的应用于工业生产的各个领域。     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

啤酒废酵母干燥工艺设计的研究

该文设计了一套适用于年产量5万吨以上啤酒厂废酵母干燥的生产工艺，提出了设计要点，并对干燥工艺进行了适用性分析。     

企业以顾客为中心的营销策略过程研究

试图构建企业以顾客为中心的营销策略过程的一般模型，并利用已有的研究成果对其构成要素进行了深入分析．在此基础上，对此模型所形成的企业营销策略循环进行分类分析，并以实例说明它们所代表的现实意义，从而为企业的决策提供帮助．     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

DESIGN AND IMPLEMENTATION OF STATE OBSERVERS IN REACTIVE DISTILLATION

This study demonstrates that state observers can be developed and applied to infer the composition profiles of reactive distillation columns from noise-contaminated temperature measurements. The design and implementation of a Kalman filter (KF) and a Luenberger observer (LO) are carried out, and their performances are quantitatively assessed. The reliability, accuracy, and robustness of the two designs method are examined and compared quantitatively. The design and implementation of a Luenberger observer are simpler and easier to carry out than those of a Kalman filter. On the other hand, a Kalman filter is found to be more robust to a noisy measurements, erroneous initial estimates, and model uncertainties. A Luenberger observer could be used for composition estimation of reactive distillation when an ideal model of the system can reasonably approximate the real system; otherwise, a Kalman filter is recommended to be applied in more practical situations.     

溶胶凝胶法聚合物/无机复合材料的研究与应用

介绍了制备聚合物/无机复合材料的溶胶凝胶原理,基本过程及制备途径,简要阐述了其在光学材料、电子材料、生物材料、涂层材料、纳米材料等领域的研究及应用进展,指出了其进一步研究的发展方向和重点。