中小型软件质量度量应用与研究

目前国内对软件质量评估还没有明确的准则和衡量标准,难以实现定量评价,运用软件度量的最新研究成果,针对中小型软件进行质量指标分析,确定度量指标体系,建立定量度量模型,最终开发软件系统,进行案例分析。     

Experiments with a hybrid interior point/combinatorial approach for network flow problems

Interior point (IP) algorithms for Min Cost Flow (MCF) problems have been shown to be competitive with combinatorial approaches, at least on some problem classes and for very large instances. This is in part due to availability of specialized crossover routines for MCF; these allow early termination of the IP approach, sparing it with the final iterations where the Karush Kuhn-Tucker (KKT) systems become more difficult to solve. As the crossover procedures are nothing but combinatorial approaches to MCF that are only allowed to perform few iterations, the IP algorithm can be seen as a complex ‘multiple crash start’ routine for the combinatorial ones. We report our experiments of allowing one primal-dual combinatorial algorithm to MCF to perform as many iterations as required to solve the problem after being warm-started by an IP approach. Our results show that the efficiency of the combined approach critically depends on the accurate selection of a set of parameters among very many possible ones, for which designing accurate guidelines appears not to be an easy task; however, they also show that the combined approach can be competitive with the original combinatorial algorithm, at least on some ‘difficult’ instances.     

基于机器视觉的隔热条尺寸测量系统

针对当前隔热条的尺寸测量仍停留在产品离线后,工作人员用卡尺测量,劳动强度大,工作效率低、测量精度易受人为因素影响的现状,本文提出将机器视觉技术引入到隔热条自动化生产线的在线尺寸检测系统中,这种非接触式测量既可以避免在测量过程中对隔热条的损坏,又可以提高测量精度和测量速度,从而达到提高测量效能的目的。     

基于P89C668单片机的智能定硫仪系统设计

该仪器根据GB214-2007《煤中全硫的测定方法》库仑滴定法原理设计,全部测试过程采用单片机自动控制,系统主要侧重于电路简单、系统抗干扰能力强、测硫精度高和控制温度科学等方面的研制。该方法与目前采用的艾士卡重量分析法和高温燃烧中和法相比具有测定迅速、结果准确的优点。     

Autonomous Visual Measurement for Accurate Setting of Workpieces in Robotic Cells

This paper introduces a new method of adapting the virtual world of an offline programming model to an actual robotic cell by attaching a CCD camera to the robot. This method requires no specific camera attachment location or optical camera calibration. Furthermore, there is no operational requirement for setting robotic camera location. Robot motion is autonomously generated to identify the camera view line. The view line is adjusted to pass through the designated target point, utilizing visual feedback motion control. This method calibrates reference points between the virtual world of an offline model to an actual robotic cell.     

Simulation Method of Dynamic Characteristics of Turbine Flow Sensor

Computational Fluid Dynamics (CFD) simulation is one of the important methods to study the performance and in-fluencing factors of turbine flow sensors. According to the working characteristics of the turbine flow sensor, the passive simulation method based on the six degrees of freedom (6-DOF) model and dynamic mesh is proposed in this paper. The reliability of the simulation method is verified by steady-state experiments and unsteady-state experiments. The results show that the trend of meter factor with flow rate acquired from the simulation is close to the experimental results, and the deviation between the simulation result and the experiment result is low with a maximum deviation of 2.88%. In the unsteady simulation study, the impeller speed changes with the inlet velocity of the turbine flow sensor, which has a good follow-up. The passive simulation method can be used to predict the dynamic performance of the turbine flow sensor.     

基于DSM与QFD技术的设计联合矩阵及其决策流程

在大型复杂设计活动中，由于缺少系统化的交流机制来保障设计过程中设计信息的及时、准确地传递，产生设计冲突，进而导致整个设计在时间上的拖延。本文以此为出发点，提出了解决上述冲突的基于DSM与QFD技术的集成设计联合矩阵及其决策流程；支持企业缩短其新产品开发的周期。     

无损检测的质量控制技术

以控制无损检测中的误判为例,介绍了质量控制技术在无损检测质量管理工作中的应用.首先利用流程图发现出现误判问题的产生环节,即缺陷的定位或定量错误.然后利用两图一表(因果图、排列图和检查表)分析引起缺陷定量或定位错误的原因.最后制定了防止误判产生的对策表.采用质量控制技术可以实现无损检测质量的持续改进.     

锻压机械打击力测量误差的加速度补偿

提出了锻压机械打击力测量中存在的问题，介绍了常用的补偿法，并通过实验验证了加速度补偿法是消除锻压机械打击力测量误差的有效途径。     

彩板涂料固化温度曲线的测定

在卷材有机涂层钢板生产中，涂料的固化温度是影响产品质量的重要因素。使用BYKOTRACK和GRADIENT－OVEN测出不同基板、不同涂料的固化温度曲线，并控制固化过程温度参数，可使每次生产都获得最佳固化温度，此而大大减少废、次品，经济效益十分显著。