泡沫沥青混合料动态性能研究

为更好地模拟泡沫沥青混合料在车辆动载作用下的动态性能，便于与国外相关研究进行比较，采用劈裂法对混合料动态性能进行研究。通过试验研究骨料类型、级配、水泥用量等对泡沫沥青混合料动态回弹模量的影响，总结了泡沫沥青混合料动静模量的关系。     

电解铝侧插自焙槽技术改造与环境保护

电解铝侧插自焙槽属于落后的生产工艺，由于其能耗高、物料消耗大、劳动强度大、环境污染严重，在国内电解铝中已开始进行大规模的淘汰改造。采用先进的预焙电解槽生产技术，降耗节能、改善生产劳动强度，环境污染得到有效治理，各项环境指标达标排放，经济技术指标提高，食业面貌发生了巨大大变化。     

含RE铝阳极中析出相的电化学行为研究

用电子探针和能谱分析技术，观察了Al-5Zn-0．05In-0．1Sn-1Mg-0．3RE阳极中主要析出相的成分，并熔炼了析出相合金．电位测量和腐蚀后铝阳极表面的电子探针面扫描分析表明：富Sn相为阳极相，富Fe相、富RE相为阴极相；Fe相是铝阳极自腐蚀微电池中的主要阴极相，温度对析出相的电化学行为有影响．     

介绍一种生产冲挤用铝合金坯料的新工艺

哈兹列特铝板带连铸连轧工艺已被成功地用于铝和铝合金冲击挤压用坯料的生产。在对哈氏四个有关用户扫描的基础上，列举了其产品及其用途，并介绍了相关工艺及其优点。     

燃气不换向蓄热式熔铝炉

蓄热式熔铝炉是一项先进节能技术，但至今在铝行业普及率不高，主要是一次性投资较大，维修费用较高。新近开发的燃气不换向蓄热式烧嘴，设备投资少、系统简化、设备故障少，使用安全可靠。     

Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.     

直流电弧炉长弧泡沫渣技术

本文指出了直流电弧炉采用长弧泡沫渣技术的必要性及该技术的发展现状，总结了炉渣物理性质，化学成分，温度和气源等对炉渣泡沫化的影响，并介绍了电炉泡沫渣的操作工艺及实际应用效果，对宝钢三期１５０ｔＤＣ－ＵＨＰ电弧炉的泡沫渣工艺提出了看法。     

Aluminum. II. Derivation of C v0from C p and comparison to C v0 calculated from anharmonic models

The specific heat at constant pressure, C _p, of aluminum measured by Ditmars, Plint, and Shukla has been reduced to the volume V ₀ appropriate for 0 K employing the Murnaghan equation. The C _v0 thus obtained is compared with the theoretical C _v0 calculated in the harmonic and the lowest-order anharmonic approximation from three different pseudopotentials (Harrison, Ashcroft, and Dagens-Rasolt-Taylor) as well as a phenomenological Morse potential. The higher-order ( ⁴) anharmonic contributions are calculated from the same nearest-neighbor Morse potential as in the lowest-order anharmonic theory. The role of the vacancy and the higher-order anharmonic contributions to C _v0 has been examined and we conclude that the ⁴ contributions to C _v0 are much smaller than the vacancy contribution. After removal of the vacancy contribution, the reduced C _v0 is found to be in excellent agreement with the Ashcroft and Harrison pseudopotentials as well as the Morse potential including the ² and ⁴ contributions to C _v0.     

空心铝型材挤压过程计算机仿真系统

试开发了一套基于计算机辅助设计和数值模拟的空心铝型材挤压过程计算机仿真系统,它涵盖了模具工艺设计的全过程,可以集成原有的和新建立的工艺设计知识。该系统包括空心型材挤压模具及坯料的参数化几何造型模块,并能分析分流桥的截面形状、分流孔的布置、焊合室的高度、工作带长度和阻流或者助流结构对金属流速分布的影响,模具的弹性变形对工作带有效长度和模孔尺寸的影响。     

Continuous electromagnetic separation of inclusion from aluminum melt using alternating current

A novel scheme about the continuous electromagnetic purification of aluminum melt was put forward based on the utilization of a square separation pipe and a 50 Hz alternating current to produce electromagnetic force. It is experimentally found that with electrical current of 400 A/cm^2, it takes only 10 s to remove 95% inclusion from aluminum melt. Comprehensive numerical simulations were carried out to investigate the dynamics mechanisms behind the process. The results show that the removal of inclusion is attributed to the cooperative effects of electromagnetic buoyancy and the secondary flow induced by the rotational electromagnetic force, and the removal efficient increases with the size of inclusion and the electrical current imposed. Theoretical predictions on the distribution and removal efficiency of inclusion were supported by the experiments.