HEAT TRANSFER BETWEEN ROUGH SURFACES IN CONTACT OVER A HIGHLY ELLIPTICAL CONTOUR AREA: COMPARISON OF EXPERIMENTAL AND NUMERICAL RESULTS

This paper describes experimental and numerical studies of heat transfer between surfaces in contact over a highly elliptical area in a gas or in vacuum. Measurements of the steady-state thermal resistance of a high aspect ratio contact formed between cylindrical steel surfaces with widely different radii of curvature (76 cm vs 0.95 cm) are reported for two levels of surface roughness (0.05 μm and 1.0 μm rms) and compared to 3-D numerical results obtained with the multigrid method. Theoretical results obtained by evaluating the contact conductance acting over each surface element within the contour area with a method developed previously for rough but nominally flat surfaces are shown to be in excellent agreement with the rough surface experimental data.     

Tube Diameter and Height Influence on the Ozonation Operating Conditions with a U-Tube

Ozone has been used for a number of years in water treatment for viricidal and bactericidal action, as well as for its oxidizing properties. Energy consumption during its use depends on the performance of the ozone generators, but also on the ozone transfer efficiency from the gas phase to the liquid phase. Therefore, it is important to use a contactor with a high transfer efficiency.A new ozonation reactor has been developed: the Deep U-Tube (DUT). This reactor works under pressure, which increases the saturation concentration of ozone at equilibrium (C ). and creates a great turbulence, which breaks the gas bubbles and increases the interfacial area of exchange. Further, this new contactor has a piston hydraulic behavior in the liquid phase, which leads to a very great efficiency and to a better reduction for all reaction kinetics.     

HEAT TRANSFER IN PARTIALLY MISCIBLE TERNARY SYSTEMS

In the study of mass transfer between partially miscible liquids, temperature perturbations have been found to have an important effect in the generation of interfacial activity. Micro- and macro-generated interfacial convection usually occurs in combination with one another even in fairly simple heat or mass transfer events. These combinations are responsible for the enhancement of mass transfer rates. In an effort to acquire a better understanding of the heat transfer effects in ternary liquid-liquid systems, temperature difference profiles were measured when contacting two partially miscible phases. A vertical and a rotational transfer cell were designed to contact the partially miscible phases without inducing external disturbances. Five thermocouples were immersed in the bottom liquid phase at predetermined positions below the interface. In order to understand the influence of the convection generated, the vertical cell was designed to hinder convection in one phase, while the rotational cell permits convection in both phases. The experimental results showed larger temperature differences in the rotational cell after the contact of the phases. Also, systems which were initially unsaturated presented larger heat effects than those in which the partially miscible solvents were initially saturated. Several parameters indicating the importance of heat effects in the ternary systems studied are reported.     

Preparation and characterization of porous carbon beads and their application in dispersing small metal crystallites

Porous carbon beads were prepared by the pyrolysis of poly(vinylidene chloride) beads that were synthesized by suspension polymerization. After prolysis treatment at 180–300 °C under argon stream, the polymeric beads were further carbonized at 1000 °C for 3 h under argon stream to acquire porous carbon beads, of which the specific surface area was about 1000 m²/g, and pore size was mainly in the width range of 0.8–1.2 nm. The carbon structure and surface chemical composition characterized by X-ray diffraction and X-ray photoelectron spectroscopy, depended on the preparation temperature and the relations between them were examined. The characterization of the carbon beads by scanning electron microscopy, atomic force microscopy presented the morphological structure of the carbon beads surface and a global view of pores. The dispersion of nickel crystallites on the carbon beads surface was characterized by electron microprobe analysis. This study reveals that uniform surface morphological structure leads to the fine dispersion of metal crystallites.     

Characteristics of epoxy resin cured with in situ polymerized curing agent

In order to improve the heat resistance of a cured epoxy resin together with reducing the viscosity of the resin composition, an epoxy resin was cured with a curing agent formed from the radical copolymerization of vinyl monomers during the cure process of the epoxy resin. N-phenylmaleimide and p-acetoxystyrene were used as vinyl monomers of the curing agent. The epoxy resin was cured by the insertion reaction of the ester group of the in situ polymerized curing agent and the epoxy group of the epoxy resin. In the cure system of the epoxy and the phenol resins, reduction of the viscosity of the resin composition was achieved by replacing some or all of the phenol resin with these monomers. When all phenol resins were replaced by these monomers, the viscosity of resin composition (0.01 Pa s at 70 °C) decreased by about 1/2000 compared with that of the system with only phenol resin (21 Pa s at 70 °C). The glass transition temperature (T_g) of the cured resin with no phenols was 174 °C, an improvement of 17 °C compared with that of the system cured with only phenol resin. The flexural strength of the new resins remained unchanged.     

溶剂沉淀法制备的聚酰胺粉末之溶剂与粉末结构和热稳定性的关系

使用粒度分布仪、白度仪、电子显微镜和差热仪测定四种溶剂沉淀法制备的聚酰胺粉末发现：每种方法所获得的粉末粒径、比表面积、白度均不相同；以乙醇 氯化钙混合溶剂制备的粉末内部具有多孔结构；以乙醇 盐酸 水混合溶剂制备的粉末热稳定性较高     

用预分解技术改造Φ4×60m预热器窑的又一成功实例

介绍南京水泥工业设计研究院用预分解生产技术对山东水泥厂Φ4×60m预热器窑烧成系统进行的成功技术改造。技改设计指标为：熟料产量保证指标1500t／d，争取指标1700t／d，熟料热耗＜3762kJ／kg，熟料28d抗压强度＞60MPa。整个工程停产施工耗时仅用48d，烧成系统技改共耗资约3000万元。技改后一次点火投料成功，且点火当月即实现72h达标考核，所有设计指标均达标。     

Electrochemical insertion of lithium ions into disordered carbons derived from reduced graphite fluoride

Both covalent (obtained by direct fluorination at high temperature) and semi-ionic carbon fluorides (synthesized at room temperature) were reduced in order to obtain disordered carbons containing very small content of fluorine and different physical properties according to the reduction treatment (chemical, thermal or electrochemical). After a physical characterization (X-ray diffraction, electron spin resonance and FT-IR spectroscopies), the electrochemical behaviours of the pristine carbon fluorides and of the treated samples were investigated during the insertion of lithium using liquid carbonate-based electrolytes (LiClO₄-EC/PC, 50:50%, v/v). Both galvanostatic and voltammetric modes were performed and revealed that the voltage profiles and the capacities differed according to the starting material and the reduction treatment. Semi-ionic carbon fluoride treated in F₂ atmosphere for 2 h at 150 °C and then chemically reduced in KOH exhibits high reversible capacities (the reversible capacity is 530 mAh g⁻¹ in the second cycle); in this case, the voltage profiles show a large flat portion at potentials lower than 0.3 V which is attributed to the insertion/deinsertion of lithium ions between the small graphene sheets and/or the absorption of pseudo metallic lithium into the microporosity of the sample. Nevertheless, a part of the lithium ions are removed at potentials higher than 0.5 V versus Li⁺/Li limiting the useful capacity.     

试论小氮肥造气工序设备的更新换代

论述小型氮肥厂近年来在煤造气工序中主要设备的更新换代问题;介绍许多优良的新设备和新技术的应用情况。     

Non-isothermal reaction-diffusion systems with thermodynamically coupled heat and mass transfer

Non-isothermal reaction-diffusion (RD) systems control the behavior of many transport and rate processes in physical, chemical, and biological systems. A considerable work has been published on mathematically coupled nonlinear differential equations of RD systems by neglecting the possible thermodynamic couplings among heat and mass fluxes, and reaction velocities. Here, the thermodynamic coupling refers that a flux occurs without its primary thermodynamic driving force, which may be gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling equations of non-isothermal RD systems with coupled heat and mass fluxes excluding the coupling of chemical reactions using the linear non-equilibrium thermodynamic approach. For a slab catalyst pellet, it shows the dynamic behavior of composition and temperature profiles obtained from the numerical solutions of non-linear partial differential equations by Mathematica for two industrial reaction systems of synthesis of vinyl chloride and dissociation of N₂O.