顶封封隔管柱的研制与应用

中原油田近年来注水压力不断升高，井况恶化严重，为此开发了顶封封隔管柱，主要阐述了管柱工况受力特点、结构、工作原理及现场使用效果。经现场较大面积的应用证明，各项性能、技术指标达到了现场要求。     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

高压玻璃钢管道的研制及在油田中的应用

本文介绍了高压玻璃钢管道的特性及在我国油田的应用情况。     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.