浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果     

3#大布袋收尘器更新改造方案的探讨

通过对3^#大布袋收尘器更新改造方案的对比分析，探讨适合工艺条件的最佳收尘器的选择途径。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

尖晶石型纳米钴蓝陶瓷颜料的制备

采用化学共沉淀法作为钴蓝颜料的制备方法,探讨了主要工艺因素对制备钴蓝颜料性能的影响,对制备的样品进行了测试与表征。结果表明:Co2+和Al3+物质的量比为1∶2.5时,制备的钴蓝样品颜色饱和度与明度最高,沉淀剂为尿素时制得的样品的粒度最小,粒度分布比较均匀。前驱体的洗涤过程采取水洗加醇洗的方法可有效减少样品的硬团聚现象,且前驱体的最佳煅烧温度为950℃左右。     

Effect of pH on the Crystallization of Homogeneously Precipitated Nanosized PZT Powder

Nanosized lead zirconate titanate (PZT) powder with Zr:Ti ratio in the morphotropic phase boundary region was synthesized by homogeneous precipitation of metal ions. The powder precipitated at 90°C and at pH 6.7 resulted single-phase perovskite lead zirconate titanate powder when calcined at 550°C and above for 4 hours in air. The solution pH and the precipitation temperature strongly affect the composition of the calcined powder. The results obtained by structural characterization of homogeneously precipitated powder were compared with that obtained from the conventional precipitation method using ammonia in terms of crystallization, homogeneity, and microstructure. The homogeneously precipitated powder showed smaller particle size, minimum agglomeration and uniform shape on calcination and annealing. Powdered samples that precipitated by homogeneous precipitation crystallized directly to perovskite PZT, without any intermediate pyrochlore phase formation. In contrast, the NH₃ precipitated powder converted to perovskite PZT via metastable pyrochlore and it showed phase segregation upon annealing at higher temperatures. The reaction kinetics has been studied by X-ray diffraction, differential thermal analysis, and differential scanning calorimetry.     

NaAlO_2-Al_2(SO_4)_3法制备拟薄水铝石成胶机理的研究

研究了拟薄水铝石和三水氧化铝的生成机理。考察了成胶pH、成胶温度对生成物类型的影响,在此基础上确定了NaAlO2溶液和Al2(SO4)3溶液成胶过程中完全中和时的临界体积比Ψ/Ψ0,在成胶过程中,当Ψ/Ψ0≤1时,NaAlO2溶液与Al2(SO4)3溶液发生中和反应生成拟薄水铝石和/或碱式硫酸铝;当Ψ/Ψ0>1时,过量的NaAlO2溶液发生自发水解反应,生成三水氧化铝。     

高纯超细氧化铝的制备

介绍一种利用氧化铝生产过程的中间物料———铝酸钠溶液 ,生产高纯超细氧化铝的方法 ,即利用钡盐净化铝酸钠溶液 ,得到A/S >10 0 0 0的精制溶液 ,再进行种分分解 ,得到超细Al(OH) 3 ,经过酸洗 ,最终得到纯度达 99 99% ,粒度 90 %小于 2 μm高纯超细氧化铝。