Effect of doping polyacrylic acid with some dopants as studied by different techniques

The molecular weight of polyacrylic acid (PAA) was determined by a viscometric method using NaNO₃ as solvent at 30°C. The specific electric conductivities (σ) of PAA as well as PAA doped with carbon black (CB), chromium oxide (Cr₂O₃), and cupferron with different concentrations (from 0.25 to 1 wt %) were measured at a temperature range 360–400 K. IR spectra of some polymers were determined and it was shown that when PAA was doped with 0.5 wt % CB, a C? O? C band appeared at 775–875 cm^?1. The positron annihilation lifetime (PAL) spectra in PAA doped with the above‐mentioned dopants were measured as a function of their concentrations. It was observed that the short lifetime intensity I₁ decreased, whereas the intermediate lifetime intensity I₂, which is related to the conductivity of the material, increased with increasing the wt % of Cr₂O₃ and cupferron as well as at low concentrations of CB. These results are discussed in terms of the conducting island model. It was found that there were distinct positive relationships between σ and I₂. © 2002 John Wiley & Sons, Inc. J Appl Polym Sci 84: 877–883, 2002; DOI 10.1002/app.10381     

Halogen-induced charge transfer polymerization of pyrrole in aqueous media

Simultaneous polymerization and doping of pyrrole have been carried out in the presence of a halogenic electron acceptor, bromine (Br₂) or iodine (I₂), in aqueous dispersion or in a two-phase solvent system. The morphology of the polypyrrole (PPY) so produced is granular and porous. The electrical conductivity of the PPY-I₂ charge transfer (CT) complex is of the order of 10¹ ohm⁻¹ cm⁻¹ while that of the PPY-Br₂ complex is about one order of magnitude less. Both complexes are stable in the atmosphere. The physicochemical properties of the PPY-I₂ and PPY-Br₂ CT complexes prepared under various experimental conditions are examined in detail.     

交联型聚醚聚氨酯的表征、力学性能及其碱金属盐络合物的导电性能

采用三羟甲基丙烷（ＴＭＰ）作交联剂与聚乙二醇（ＰＥＯ－１５４０）和甲苯二异氰酸酯（ＴＤＩ）反应，得到了具有较好力学性能的交联型聚醚聚氨酯（ＰＥＵ），该聚合物与ＬｉＣｌＯ４的结合物具有较高的室温电导率（σ３０℃＝１．８７×１０￣（－４）Ｓ／ｃｍ）。采用全反射红外光谱（ＡＴＲ－ＩＲ）对聚合物的结构进行了表征。对聚合物的组成、不同ＴＤＩ类型及络合盐浓度对聚合物力学性能及其络合物电导率的影响进行了探讨。低度交联聚合物的络合物，其电导率与温度的关系符合建立在自由体积理论上的ＶＴＦ方程，表明络合物中离子的传导主要是在无定形区域进行，与自由体积有关。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

添加CaF2-YF3的AlN陶瓷的热导率

用CaF2和YF3做添加剂，在1750℃制备了热导率高于170W/m.K的的AlN陶瓷，并用XRD和SEM研究了AlN陶瓷在烧结过程中的相组成，微结构以及晶格参数的变化，并讨论了其对热导率的影响，研究发现，当使用CaF2-YF3做添加剂时，微结构差异对AlN陶瓷热导率的影响很小，AlN陶瓷的热导率主要由AlN晶格氧缺陷浓度决定，由于CaF2-YF3能有效降低AlN颗粒表面的氧含量，从而有利于获得高的热导率。     

导流能力测试系统的研制

压裂后裂缝的导流能力直接关系着压裂缝的渗流能力，是客观评价压裂效果的重要指标之一。文章介绍了基于AT89C52单片机的导流能力测试系统的系统要求、测试原理以及其设计方案，阐述了各个测控通道，给出了测控系统电路方框图。     

High temperature transport kinetics in heteroepitaxial LaFeO3 thin films

Heteroepitaxial LaFeO₃(1 1 0) thin films with a thickness of 150 nm were grown on LaAlO₃(0 0 1) by reactive sputtering in an inverted cylindrical magnetron geometry. Equilibrium conductivity was measured as a function of partial pressure of oxygen at T=1000 °C, and logσ plotted vs. logP(O₂) showed a minimum in conductivity for P(O₂)=10⁻¹¹ atm and a linear response between 10⁻¹⁰ and 1 atm. This linear response makes thin films of LaFeO₃ a promising material for oxygen sensor applications. We have also measured the time response of the film conductivity upon an abrupt change in the partial pressure of ambient oxygen from 10⁻² to 10⁻³ atm, which was determined at 60 s for T=700 °C and <3.5 s at T=1000 °C.     

新型雷达干扰材料--导电聚苯胺

导电聚苯胺(PAN)是一种具有潜在应用价值的新型射频与微波吸收剂。在聚苯胺中添加各种导电填料如碳黑、石墨、金属粉或通过化学掺杂，可使电导率得到显著提高，而且比重小、易加工成型。本文简述其合成方法，用XRD、FTIR对其结构进行表征，初步测试了该材料对毫米波雷达的衰减效果，测试结果表明导电聚苯胺在8mm波波段具有衰减性。     

硅压力传感器的可靠性测试

硅压力传感器的可靠性测试技术研究受到了国内外的重视，对它的测试项目及其加速寿命测试方法进行了综述。     

Fiber-Optic Sensors: Technical and Market Trends

Progress in the area of fiber-optic sensors throughout the world since 1990 is analyzed. Current technical and market trends as well as the use of sensors in industry and health care are considered. Market forecasts for the use of fiber-optic sensors are given.