Microtensile versus microshear bond strength between dental adhesives and the dentin substrate

This study evaluated the performance of different bonding tests on the bond strength of three adhesive systems to dentin. Forty-eight bovine incisors were used in the study, which were allocated in two groups according to the bond strength test performed: microtensile (µTBS) or microshear (µSBS). Also, each group was divided in three subgroups according to the adhesive system applied: Single Bond (SB), Prime & Bond (PB) and XP Bond (XPB) (n=8). The teeth were prepared according to each bond strength test protocol, and then the specimens were tested in an universal testing machine (EMIC). The data were submitted to two-way ANOVA (bond strength test and adhesive system type factors) and Tukey's post hoc test (α=0.05). The µTBS results were higher for all the adhesives when compared to the µSBS ones. Within the µTBS results, SB showed higher bond strength than PB and XPB, which showed similar adhesive performance among each other; within the µSBS results, all the adhesives presented similar bond strength values to dentin. The µTBS test detected differences between the adhesive systems evaluated; in contrast, the µSBS test was less discriminating in evaluating the adhesive performance of the materials tested.     

ORDERING TRANSITIONS IN LIQUID CRYSTALS PERMIT IMAGING OF SPATIAL AND TEMPORAL PATTERNS FORMED BY PROTEINS PENETRATING INTO LIPID-LADEN INTERFACES

Recent studies have reported that full monolayers of L-α-dilaurylphosphatidylcholine (L-DLPC) and D-α-dipalmitoylphosphatidylcholine (D-DPPC) formed at interfaces between thermotropic liquid crystals (LCs) and aqueous phases lead to homeotropic (perpendicular) orientations of nematic LCs and that specific binding of proteins to these interfaces (such as phospholipase A ₂ binding to D-DPPC) can trigger orientational ordering transitions in the liquid crystals. We report on the nonspecific interactions of proteins with aqueous-LC interfaces decorated with partial monolayer coverage of L-DLPC. Whereas nonspecific interactions of four proteins (cytochrome c, bovine serum albumin, immunoglobulins, and neutravidin) do not perturb the ordering of the LC when a full monolayer of L-DLPC is assembled at the aqueous-LC interface, we observe patterned orientational transitions in the LC that reflect penetration of proteins into the interface of the LC with partial monolayer coverage of L-DLPC. The spatial patterns formed by the proteins and lipids at the interface are surprisingly complex, and in some cases the protein domains are found to compartmentalize lipid within the interfaces. These results suggest that phospholipid-decorated interfaces between thermotropic liquid crystals and aqueous phases offer the basis of a simple and versatile tool to study the spatial organization and dynamics of protein networks formed at mobile, lipid-decorated interfaces.     

Understanding Interactive Legends: a Comparative Evaluation with Standard Widgets

Interactive information visualization systems rely on widgets to allow users to interact with the data and modify the representation. We define interactive legends as a class of controls combining the visual representation of static legends and interaction mechanisms of widgets. As interactive legends start to appear in popular websites, we categorize their designs for common data types and evaluate their effectiveness compare to standard widgets. Results suggest that 1) interactive legends can lead to faster perception of the mapping between data values and visual encodings and 2) interaction time is affected differently depending on the data type. Additionally, our study indicates superiority both in terms of perception and interaction of ordinal controls over numerical ones. Numerical techniques are mostly used in today's systems. By providing solutions to allowing users to modify ranges interactively, we believe that interactive legends make it possible to increase the use of ordinal techniques for visual exploration.     

Impact of spinel forming systems (Fe-/Mg-/Mn-Al-O) as functional coating materials for carbon-bonded alumina filters on steel melt filtration

Since solid, non-metallic inclusions influence considerably the quality of casted steel products, carbon-bonded alumina foam filters are used in secondary metallurgical treatments to remove these particles from steel melts. In order to attain a significant improvement of the filtration process, five different carbonaceous spinel compounds from the Fe-/Mg-/Mn-Al-O systems are applied on carbon-bonded alumina filters in this study and investigated with regard of their filtration efficiency. However, these spinel compounds decompose partially during sintering at 1400?°C under reducing atmosphere, wherefore the resulting coatings contain not only spinel compounds, but also oxidic and metallic components. The subsequent interaction with molten steel leads to the development of multicrystal structures on the filter surface, which stem from interfacial reactions between coating materials, molten steel, and inclusions. As a result of this procedure, a reduction of almost 60% alumina inclusions is measured with the aid of an automatic SEM, whereby spinel compounds from the Fe-Mn-Al-O system achieve highest filtration efficiencies.     

ADHESION OF ELASTOMERS: DWELL TIME EFFECTS

The strength of adhesion of elastomers to rigid substrates generally increases with time of contact. This effect has been studied for samples of butyl and chlorobutyl rubber adhering to some rigid substrates. The peel strength increased continuously over long periods of contact until in some cases failure became cohesive within the elastomer layer. At higher temperatures the strength increased more rapidly, consistent with the WLF relation governing molecular motions. It is postulated that slow molecular rearrangements occur at the interface and increase the bond strength. A criterion for the observed transition from interfacial to cohesive failure is suggested.     

Extreme wet adhesion of a novel epoxy-amine coating on aluminum alloy 2024-T3

Amine-epoxy polymer systems are widely used, for example as matrix materials for structural composites employed in aerospace industry and in industrial coatings on metal substrates for corrosion protection. This work focuses on the investigation of different epoxy-amine coatings on the adhesion performance on aluminum AA-2024 substrates. Two different epoxies (Epikote 828 (aromatic) and Eponex 1510 (aliphatic)) and four different amines (1,8-diaminooctane, Dytek A, Jeffamine EDR148 and Jeffamine D230) as curing agent were used in different stoichiometric ratios. These different epoxy-amine coatings were characterized using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), tensile tests (pull-off) and water-uptake measurements. Pull-off tests in dry conditions showed comparable adhesion of the coatings. Surprisingly, pull-off results showed after water soaking a higher wet adhesion of the coatings prepared with Eponex 1510 as compared to coatings prepared with Epikote 828. Moreover, the combination of Eponex 1510-Jeffamine EDR148 coatings resulted in high adhesion values (∼7 MPa) with pull-off tests and these values did not change after immersion for two weeks in water. This combination shows extreme good wet adhesion performance as compared to any other epoxy-amine coating. Complete recovery was demonstrated of the adhesion of Eponex 1510-Jeffamine D230 coating after being immersed for two weeks in water and dried for two weeks. Furthermore, in contrast with Epikote 828 water uptake measurements showed almost nil water uptake for all coatings prepared with Eponex 1510. Optical microscopy investigations on the residues of the coatings after pull-off tests revealed adhesive failure in wet condition for Epikote 828, while coatings prepared with Eponex 1510 showed cohesive failure.     

Effect of annealing and silylation on the strength of melt-spun Ni–Mn–Ga fibres and their adhesion to epoxy

Single crystals of ferromagnetic Ni–Mn–Ga shape memory alloys show magnetic-field and stress induced twinning, leading to shape memory. Adaptive composites can thus be produced by embedding single crystalline particles or bamboo-structured Ni–Mn–Ga fibres into a polymer matrix. To guarantee a durable performance of these composites, adhesion between reinforcement phase and matrix should be quantified and optimised. The influence of annealing and surface treatment with an aminosilane of melt-spun Ni–Mn–Ga fibres on their strength and adhesion to an epoxy matrix was investigated using single fibre tension and fragmentation tests. Annealing of the melt-spun Ni–Mn–Ga fibres changed the surface from a “pimpled” to a smooth microstructure. This resulted in a reduced adhesion of the annealed fibres in comparison to the as-spun fibres embedded in an epoxy matrix. As-spun fibres exhibited an interfacial shear strength (IFSS) comparable to the shear strength of the epoxy matrix so that the silylation did not change the adhesion significantly. For the annealed fibres, the silane treatment improved the IFSS by 67%. Furthermore, the silylation increased the fracture strength of the Ni–Mn–Ga fibres due to surface flaw healing or forming of a protective surface coating.     

基于SOA架构的立法决策支持系统研究

党的十八大报告将“全面推进依法治国”确立为推进政治建设和政治体制改革的重要任务,而立法工作是其中最重要的基础工作.立法工作相关信息化系统的建设为立法工作提供了重要技术支撑,而随着立法工作中各项业务系统的联系性需要更加紧密,集成度要求越来越高,信息资源的共享范围需要越来越广,使得各业务系统的互联互通和流程规范化等问题成为了立法工作信息化建设必须要面对的一个关键问题.单个的业务系统拓展、功能强化、硬件升级已经不能满足要求,而基于ESB（企业服务总线enterprise service bus）的架构平台,以服务作为基本管理单元提供了很好的解决方案,它可以消除不同业务系统之间的技术差异,让不同业务系统协调运作,从而实现不同业务之间的通信与资源整合.     

Visualizing Group Structures in Graphs: A Survey

Graph visualizations encode relationships between objects. Abstracting the objects into group structures provides an overview of the data. Groups can be disjoint or overlapping, and might be organized hierarchically. However, the underlying graph still needs to be represented for analyzing the data in more depth. This work surveys research in visualizing group structures as part of graph diagrams. A particular focus is the explicit visual encoding of groups, rather than only using graph layout to indicate groups implicitly. We introduce a taxonomy of visualization techniques structuring the field into four main categories: visual node attributes vary properties of the node representation to encode the grouping, juxtaposed approaches use two separate visualizations, superimposed techniques work with two aligned visual layers, and embedded visualizations tightly integrate group and graph representation. The derived taxonomies for group structure and visualization types are also applied to group visualizations of edges. We survey group‐only, group–node, group–edge and group–network tasks that are described in the literature as use cases of group visualizations. We discuss results from evaluations of existing visualization techniques as well as main areas of application. Finally, we report future challenges based on interviews we conducted with leading researchers of the field.     

Visualizing Waypoints‐Constrained Origin‐Destination Patterns for Massive Transportation Data

Origin‐destination (OD) pattern is a highly useful means for transportation research since it summarizes urban dynamics and human mobility. However, existing visual analytics are insufficient for certain OD analytical tasks needed in transport research. For example, transport researchers are interested in path‐related movements across congested roads, besides global patterns over the entire domain. Driven by this need, we propose waypoints‐constrained OD visual analytics, a new approach for exploring path‐related OD patterns in an urban transportation network. First, we use hashing‐based query to support interactive filtering of trajectories through user‐specified waypoints. Second, we elaborate a set of design principles and rules, and derive a novel unified visual representation called the waypoints‐constrained OD view by carefully considering the OD flow presentation, the temporal variation, spatial layout and user interaction. Finally, we demonstrate the effectiveness of our interface with two case studies and expert interviews with five transportation experts.