WINDOWS系统中高效串行通信的实现

介绍了windows环境下串行通信的核心，并以VC 为开发工具给出了I／O函数与API通信函数实现串行通信的具体编程步骤。     

Applications and exploitation of Virtual Instruments based on Delphi6

This paper introduces hardware connections between computer and intellectualized instrument based on 89c51 sin-glechip .It gives the techniques to compile internet applications of Virtual Instruments with Delphi6.     

Heavy arsenic doping of silicon grown by atmospheric pressure selective epitaxial chemical vapor deposition

Selective epitaxial Si with a high arsenic concentration of 2.2×10¹⁹ atoms/cm³ was deposited at a high growth rate of 3.3 nm/min under atmospheric pressure. It was confirmed that this method had excellent selectivity and produced films having good crystalline quality, abrupt dopant profiles at the interfaces, and smooth surfaces. The growth mechanism is discussed in terms of the relationship between the effects of arsenic surface segregation and etching by hydrogen chloride.     

Network and device-level impacts: performance and reliability of active I/O storage systems

Distributed active storage architectures are designed to offload user-level processing to the peripheral from the host servers. In this paper, we report preliminary investigation on performance and fault recovery designs, as impacted by emerging storage interconnect protocols and state-of-the-art storage devices. Empirical results obtained using validated device-level and interconnect data demonstrate the significance of the said parameters on the overall system performance and reliability.     

Study of the effective parameters on mechanical and electrical properties of carbon black filled PP/PA6 microfibrillar composites

In this study the electrical and mechanical properties of microfibrillar polypropylene (PP)/polyamide6 (PA6) blend filled with super conductive carbon black (CB) have been investigated. In situ microfibrillar PP/PA6 composites filled with CB are produced using a single screw extruder equipped with a spinneret. Glycidyl methacrylate (GMA) grafted polypropylene (PP-g-GMA) is used as the compatibilizer. To investigate the effects of extensional flow on the microstructure, electrical and mechanical properties, three adaptors with various convergence angles were designed, prepared and applied between the extruder and the spinneret. To optimize the effects of processing and material parameters on the electrical and mechanical properties, the Taguchi method of experimental design is used. Material and processing factors which are studied include: concentration of PA6, compatibilizer level, CB concentration, drawing speed of melt spinning line, adaptor angle, order of mixing and temperature profile along the extruder. The results show an increase in DC conductivity of up to 10¹¹ times in comparison with pure PA6, by increasing the concentration of CB, drawing speed, adaptor angle and optimizing other parameters. By optimizing processing and material factors studied here, strength of microfibrillar structured composites is increased of up to 80% in comparison to pure PP.     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

固体超强酸S_2O_8~(2-)/SnO_2-SiO_2催化合成环己酮1,2-丙二醇缩酮

采用沉淀-浸渍法制备了固体超强酸S2O28-/SnO2-SiO2,以它为催化剂催化环己酮和1,2-丙二醇合成了环己酮1,2-丙二醇缩酮;考察了带水剂种类及用量、酮醇摩尔比、催化剂用量、反应时间对产品收率的影响,并用正交实验对反应条件进行了优化。实验结果表明,适宜的反应条件为:n(环己酮)∶n(1,2-丙二醇)=1∶1.6、催化剂用量为反应物料总质量的2.0%、带水剂环己烷用量5.0mL、反应时间50min。在此条件下,环己酮1,2-丙二醇缩酮收率达到91.47%;催化剂的稳定性良好,在重复使用5次后环己酮1,2-丙二醇缩酮收率为82.20%,活性下降的主要原因为催化剂表面积碳和吸附了有机物;经傅里叶变换红外光谱和气相色谱质谱分析表明,产物为环己酮1,2-丙二醇缩酮,纯度为100%。     

溶液温度对电化学沉积氧化亚铜薄膜相成分和显微结构的影响

用电化学方法在不锈钢基体上沉积多晶Ｃｕ２Ｏ薄膜并用Ｘ射线衍射和扫描电进行了分析研究了溶液温度对薄膜相组成、晶粒尺寸和择优取向的影响，当溶液的ＰＨ＝９，温度低于５０℃时得到的是Ｃｕ２Ｏ／Ｃｕ复相薄膜，纯Ｃｕ２Ｏ薄膜可在溶液温度高于５０℃时获得，纯Ｃｕ２Ｏ薄膜具有（１００）择优取向，实验发现薄膜的晶粒尺寸随溶液温度的增加从０．１２μｍ增加到０．６５μｍ。     

Structural modelling of coprecipitated VTiO catalysts

A statistical study of the particle shape and size of pure V₂O₅ and TiO₂, and samples of coprecipitated V₂O₅---TiO₂ catalysts with different V/Ti ratios, has been performed. They were also characterized by XRD, EDAX, SEM and XPS. The results showed that pure vanadium pentoxide is compose by large square or needle-shaped particles, while pure titanium dioxide has small and rounded ones. VTiO samples presented an area and shape, depending on the V/Ti ratio.

These results and the spectroscopical characterization conducted to a particle model of the catalysts. Those VOTi samples with high V/Ti ratio would have large V₂O₅ crystals acting as support of a V/TiO₂ solid solution. In contrast, those samples with a low V/Ti ratio, would have the solid solution supporting vanadium pentoxide crystals.