Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Efficiency and effectiveness enhancement of an intercooler of two‐stage air compressor by low‐cost Al2O3/water nanofluids

The present study was aimed to utilize low‐cost alumina (Al₂O₃) nanoparticles for improving the heat transfer behavior in an intercooler of two‐stage air compressor. Experimental investigation was carried out with three different volume concentrations of 0.5%, 0.75%, and 1.0% Al₂O₃/water nanofluids to assess the performance of the intercooler, that is, counterflow heat exchanger at different loads. Thermal properties such as thermal conductivity and overall heat transfer coefficient of nanofluid increased substantially with increasing concentration of Al₂O₃ nanoparticles. Specific heat capacity of nanofluids were lower than base water. The intercooler performance parameters such as effectiveness and efficiency improved appreciably with the employment of nanofluid. The efficiency increased by about 6.1% with maximum concentration of nanofluid, that is, 1% at 3‐bar compressor load. It is concluded from the study that high concentration of Al₂O₃ nanoparticles dispersion in water would offer better heat transfer performance of the intercooler.     

Al2O3陶瓷激光铣削试验研究

采用Nd∶YAG脉冲激光器对Al2 O3陶瓷进行铣削加工试验。系统研究了工艺参数对铣削量和铣削面质量的影响规律 ,并利用优化的铣削工艺对Al2 O3陶瓷进行多种形状的铣削加工。     

Thaumasite––direct, woodfordite and other possible formation routes

Two main formation routes for thaumasite exist below 15 °C. One is the direct route from C–S–H reacting with appropriate carbonate, sulfate, Ca²⁺ ions and excess water. The other route is the woodfordite route from ettringite reacting with C–S–H, carbonate, Ca²⁺ ions and excess water, in which thaumasite arises through the intermediate formation of the solid solution woodfordite. The woodfordite route for thaumasite formation appears to be relatively quicker (although still slow) than the direct route, presumably because with the former the ettringite already has the octahedral [M(OH)₆] units that can facilitate the critical change from [Al(OH)₆]³⁻ to [Si(OH)₆]²⁻ groupings. Both routes are mutually dependent on each other. The presence of magnesium salts can modify the path to thaumasite formation. High pressure might be able to stabilise [Si(OH)₆]²⁻ groupings and allow thaumasite to become formed above 15 °C. This possibility is discussed.     

Windows2000设备驱动程序即插即用的实现

概述了Windows2000即插即用系统组成及其实现过程,结合实例介绍了Windows2000设备驱动程序如何支持用户即插即用的功能。