基于缓冲器的编码器接口扩展方法研究

在数据采集测控系统中,用于检测的绝对值角度编码器的输出很多是基于SSI接口,采用SSI接口的绝对值角度编码器输出有时需要连接到多个不同的独立测控系统,由于SSI接口是单访问接口,多主机共享往往是较难解决又不得不解决的问题,本文提出了一种缓冲式并行读取绝对值角度编码器值的方法,实现了信号的并行读取,并给出了硬件和软件设计的思想和方法。     

热轧板常化温度对冷轧无取向电工钢退火组织和磁性能的影响

研究了≤0．005％C-2．5％-2．8％Si的2．5mm热轧电工钢板在850—1100℃常化对0．5mm冷轧板880℃＋950℃退火后组织和磁性能的影响。结果表明，热轧板常化温度升高，冷轧板退火后的再结晶晶粒增大，铁损降低，磁感呈单调递增趋势；热轧板常化温度超过1000℃，因第2相固溶而后弥散析出，退火冷轧晶粒细化，铁损增加，因此该钢热轧板最佳常化温度为1000℃。     

氧化铝熟料窑内衬改进与提产降耗

介绍采用复合型内衬砖和耐热钢扬料板等措施对熟料窑内衬进行的改进,提高了窑内物料的热交换效率和窑内衬的保温效果,为窑内热工制度的改善创造条件,提高了窑台时产能,达到了节能降耗目的.     

谈谈确定"停工检测点" "质量见证点"的方法

通过制造4台我国特大型非标冶炼回转炉的实践,以详实的实例,总结性地介绍了在特大型非标设备的制造中,怎样运用技术确定“停工检测点”、“质量见证点”,完成设备制造的成功经验。     

铜回转式阳极炉燃煤工艺技术的探讨

介绍了云南铜业股份有限公司利用新建的2台350t回转式阳极炉进行以粉煤作为燃料的工艺技术开发情况,提出了铜火法精炼回转式阳极炉用粉煤作燃料在工艺和工程施工中存在的问题和难点,对比分析了燃煤回转式阳极炉具有的优势。     

超细晶WC-Co硬质合金的发展及其应用

本文概括地综述了超细晶WC-Co硬质合金在制备工艺和检测技术等方面的发展情况,以汽车工业用刀具加工为实例,介绍了超细晶硬质合金的应用情况,并讨论了其发展前景。     

连铸坯热送热装设备设计与应用

介绍了福建三钢闽光股份有限公司连铸坯热送热装工艺及设备,对输送辊道、横移机、转盘的功率进行计算,并阐述了连铸坯热送热装技术及设备在轧钢生产上的经济效益.     

炭素煅烧自动控制系统的设计与实现

针对目前回转窑炭素煅烧存在的工况不稳定和石油焦回收率低等问题,在分析了煅烧工艺中煅烧温度场对煅后焦质量的影响后,分别对温度场影响最大的给料量和窑尾负压进行了恒料恒压控制系统的设计。该系统利用自校正控制技术和PID技术分别实现了给料量和负压的恒定,同时根据现场需要完成了煅烧过程重要参数的监视、故障的在线诊断和控制方式间无扰切换等功能。实际运行表明系统可靠性高,实用性好。     

Nanoscale Magnetic Behavior of C60 Thin Films in Earth Magnetic Field under Polarization Light Influences

Magnetic behavior of C₆₀ thin films in the Earth's magnetic field under polarization light influence is presented. Transformation of magnetic field for two fullerene thin films of different thickness is investigated. Two proton magnetometers were used for these measurements. Samples of 30 nm and 250 nm thickness illustrate a significant change of magnetic field intensity under the influence of polarization light, in range from 3.4 to 12.9 nT, for 200 measurement data per sample.     

Analysis and Reduction of Ultrasonic Pitting Defects on Hard Disk Surfaces

It has become of paramount importance to be able to perform failure analysis of defects on hard disk surfaces quickly and accurately. In this study, ultrasonic pitting defects on hard disk surfaces were investigated. A new electrical tagging pattern system, which directly translated the channel bits to magnetic transitions during writing of the magnetic pattern around a defect, was used in the failure analysis of magnetic recording disks to mark defective sectors. With the help of the Kerr magneto-effect, the defective sectors were effectively located for further failure analysis. Results of the failure analysis revealed that there was 30% to 40% loss of the recorded magnetic bit signal due to an increase in the gap between a recording head and a hard disk surface with ultrasonic pitting defects. The experiments performed indicated that low ultrasonic power for disk cleaning could reduce the ultrasonic pitting defects significantly. The maximum failure rate due to single-type ultrasonic pitting defects was reduced from 33.4% to 16.7%, while the maximum failure rate due to cluster-type ultrasonic pitting defects was reduced from 11.1% to 5%.