溅射靶材的应用及制备初探

随着电子及信息产业突飞猛进的发展，世界溅射靶材的需求越来越多，本文介绍了靶材的发展概况、分类和应用情况，以及靶材的特性要求．探讨Ni-Cr合金靶材的制备工艺，结果表明，产品能满足靶材特性要求。     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

Hydrogen Absorption and Release Behavior in Hydrogen Decrepitation Process of Nd-Fe-B Alloys

The behavior of hydrogen absorption and release in hydrogen decrepitation (HD) process of Nd-Fe-B alloys were investigated. The results reveal that the reactivity and the amount of hydrogen absorption in HD process are related to the surface activity of the alloy so that the fresh and active surface has a higher efficiency. The presence of Nd-rich phase at the grain boundary is an essential factor of the HD activity of the alloy at room temperature. On degassing, hydrogen is released from the HD powder continuously with increasing temperature. And the residual hydrogen is as low as 0.0015% at 1073K, which shows that the hydrogen is almost exhaused. It is feasible to remove the hydrogen from the HD powder by heating treatment at the temperature of 523-723K for 1h prior to the magnetic field forming in order to decrease the harmful effect of hydrogen on the easy axis alignment of HD magnet.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

真空熔炼高压气体雾化制粉技术及设备

介绍了气体雾化粉的品种、用途及工业化生产。还介绍了真空熔炼-高压气体雾化制粉所需的设备。     

Some kinetic aspects of unsteady-state partial oxidation reactions. Dynamic processes on metal oxide surfaces

It is shown that steady-state kinetic data do not allow the discrimination between the redox and associated mechanisms of the partial oxidation reactions. A discrimination between these mechanisms was performed using transient experiments. The obtained rate expressions are in agreement with experimental kinetic data for catalytic partial oxidation of o-xylene.

An influence of the conjugate oxidation of a catalyst surface on dynamics and kinetics of the heterogeneous catalytic oxidative reactions is considered. Computing simulation of methane oxidative coupling of methane reaction at lowered temperature and elevated pressure has been performed. It showed that the reaction order with respect to oxygen exceeding unity is consistent with the chain branching mechanism of the reaction in the presence of TiSi₂ and TiB₂ and showed the important role of the branching chain cycles in the low-temperature OCM reaction at elevated pressure.