考虑热不协调性的镍基单晶合金细观力学分析SCIEI

基于镍基单晶合金的细观结构特征，本文建立两个微胞模型对热不协调性作了系统的模型计算和分析．微胞模型１是以一个γ和γ’为考察对象，微胞模型２是以多个γ和γ’为考察对象，详细的分析表明，这两个模型有一定的等效性，但模型２可分析边界条件更宽的情况．基于微胞模型，对两相合金的临界分切应力进行了分析，结果表明，宏观临界分切应力可用考虑热不协调性的有限元法来处理，所得结果还可推广到较大的γ’相体积分数ｆ的情况．考察了热不协调性对回火状态时γ’形状变化的影响，初步的定量分析表明，热内应力是γ’粗化的一个主要驱动力．     

FRACTAL ANALYSES OF DIRECTIONAL SOLIDIFICATION BEHAVIOR OF A Ni-BASE SUPERALLOY

The morphology of solid/liquid interface of a directionally solidification process is describedby means of fractal analysis,and the relations among the fractal dimension of the solid/liq-uid interface,solidification rate,dendrite arm space and the phosphorus content of the test al-loys have been given.It was found that the increase of the solidification rate and the phos-phorus content of the test alloy will lead to a increase,following the regularity of exponentialfunction,in the fractal dimension of solid/liquid interface.Furthermore,by combining thefractal theory and the thermodynamic principle with the measured results,it has been provedthat the fractal dimension is not only a kind of simple geometrical parameter used in des-cribing irregular geometry,but also a state function depending the change of solidificationparameters and chemical compositions.     

Joining alumina to inconel 600 and UMCo-50 superalloys using an Sn10Ag4Ti active filler metal

Alumina ceramics were brazed to Inconel 600 and UMCo-50 superalloys at 900 °C for 10 min using an Sn10Ag4Ti active filler metal. The brazing filler showed good wettability on alumina and superalloys. The flexural strengths were 69 and 57 MPa for alumina/Inconel 600 and alumina/UMCo-50 joints, respectively. In both cases, the brazed specimens fractured along the Sn10Ag4Ti/superalloy interfaces after four-point bending tests. Electron probe microanalysis (EPMA) elemental mapping revealed that the Ni of Inconel 600 and the Co of UMCo-50 dissolved into Sn10Ag4Ti filler metal, which serves to reinforce the weak Sn10Ag4Ti matrix.     

Studies on the hot corrosion of a nickel-base superalloy,Udimet 700

The hot corrosion of a nickel-base superalloy, Udimet 700, has been studied in the temperature range 900–950°C. The effect of the amount of Na ₂SO₄ on the corrosion kinetics was determined. Large weight gains and severe corrosion were associated with two different modes of degradation: (1) formation of large, interconnected sulfides beneath the external scale, and (2) formation of a Na₂MoO₄-MoO₃ melt. The corrosion due to formation of the Na₂MoO₄-MoO₃ melt occurred for all the salt-coating thicknesses, whereas, large sulfides were formed only for the heavier coatings of Na₂SO₄. The formation of Na₂MoO₄-MoO₃ melt required an induction period, and the length of the induction period was observed to be a function of the amount of Na₂SO₄ and of temperature.Work funded under NASA Grant NCC 3-43.     

GH4169线性摩擦焊接头的焊合率与弯曲强度

论述了高温合金GH4169线性摩擦焊的试验过程。分析了弯曲强度、断裂挠度与焊合率之间的关系及接头的金相组织。结果表明,GH4169线性摩擦焊接头的弯曲强度与焊合率成正比线性关系,断口为韧性断口;断裂强度受摩擦时间的影响较大。     

The Influence of High Temperature Exposure on the Wear Performance of a Ni Based Alloy PTA Coating

Degradation phenomena like wear and corrosion, may have their effects accelerated as components operate at high temperature. The aim of this work is to make an indirect evaluation of the influence of high temperature exposure on wear behavior of Ni coatings. A Ni-Cr-Mo-W alloy, was deposited with Plasma Transferred Arc (PTA) process. An indirect approach based on the Ahrrenius relationship was used to evaluated long time exposures at high temperatures. To simulate longer exposures at lower temperatures, coatings were exposed to higher temperatures for the same time interval. So coatings were soaked in an air furnace at 650℃, 1000℃ and 1200℃. Metal/metal wear behavior was evaluated by pin-on-disc tests. Pins were removed from the coatings by eletrodischarge machining and rubbed against a VC31 quenched and tempered tool steel. Two sets of wear tests were run at 2m/s, for different loads (0.5, 1.0, 2.0 and 3.0Kg) and for different sliding distances (120, 720, 1080, 1440 and 1800m).Coatings characterization was done by scanning electronic microscopy and Vickers microhardness. Results showed as temperature is increased, coatings wear performance is altered,and this is associated with microstructural changes.     

IC-6高温合金及其防护性涂层的摩擦特性

采用电弧离子镀技术在IC－高温合金上沉积NiCrAlY涂层。研究了NiCrAlY涂层及IC－6高温合金在室温和600℃空气中无润滑状态下，以K17高温合金为摩擦副的摩擦特性。采用带有能谱的扫描电镜（SEM／EDX）分析IC－6高温合金和NiCrAlY涂层磨损表面的形貌和成分。实验结果表明，室温条件下摩擦时，一些碎屑从K17合金上脱落下来，在IC－6合金及NiCrAlY涂层表面上形成磨粒，随着摩擦时间延长，磨损表面元素发生氧化。试样在环境温度在600℃摩擦时，NiCrAlY涂层的表面比较快的形成氧化膜，减少金属－金属间的直接接触。环境温度升高后，摩擦表面温度也随之升高，氧化物的粘滞性增强，600℃时，合金和涂层摩擦系数都有不同程度的减小。     

镍基高温合金真空感应熔炼脱氮的研究

研究了采用CaO坩埚真空感应熔炼镍基高温合金过程中的脱氮行为.试验表明在精炼过程中加Al对脱氮有促进作用;加Ti则对脱氮有明显不利影响;提高熔炼时的真空度是促进脱氮的有力措施.     

APPLICATION OF d-ELECTRON ALLOY DESIGN THEORY TO DEVELOPMENT OF HOT CORROSION RESISTANT Ni-BASE SINGLE CRYSTAL SUPERALLOYS——Ⅰ Characterization of Phase Stability

为应用d-电子合金设计理论(或新相分计算法(New PHACOMP))设计发展新型抗热腐蚀单晶高温合金,首先对高Cr抗热腐蚀IN738LC系列合金Ni—16Cr—9.5Al—4.0Ti-8.0Co—0.55Nb—0.06Zr—0.05B—0.47C-Ta—W—Mo(at-％)的相稳定性进行了综合评价得出抑制σ相析出的稳定性临界条件为Mdt<0.991或Mdγ<0.93同时证明这两个临界电子参数具有等价性,可以用Mdt代替Mdγ简化合金设计过程.这一结果可适用于其它高Cr系列抗热腐蚀镍基合金的d-电子合金设计