结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

Simulation by Slepian method of plastic displacements of Gaussian process excited multistory shear frame

The object of study is a stationary Gaussian white noise excited multi-degree-of-freedom (MDOF) linear elastic, ideal plastic, linearly damped, statically determinate oscillator with several potential elements of ideal plastic yielding. Specifically the study is exemplified for a plane multistory shear frame with rigid traverses where all the connecting columns except the columns in one or more of the bottom floors have finite symmetrical yield limits. The white noise excitation acts on the mass of the first floor making the movement of the elastic bottom floors simulate a ground motion that interacts with the structure above the bottom floors. The method of study is so-called Slepian model simulation and is in principle the same for other statically determinate MDOF elasto-plastic oscillators of the considered type. The method is fast as compared to direct simulation and provides results that give good insight in the behavior of the plastic displacement response process.     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

Locked discrete event systems: How to model and how to unlock

To model qualitative aspects of discrete event systems, i.e., the order of the events is of sole importance, we use a triple consisting of the set of all possible events (the alphabet), the set of all behavior (possible strings of events), and the set of all tasks (completed behavior). We use this view to model synchronous as well as asynchronous connection of systems. Moreover, it is easy to define notions like deadlock and livelock in this view. We give a method to construct a second system that, in connection with the original system, gets rid of its deadlock and/or livelock. A state-space representation is introduced. In this representation computations can be done effectively.     

聚电解质溶液分子热力学模型

<正>链状聚电解质由于是长链大分子又有很高的电荷密度,其溶液即使在极低的浓度下仍具有很强的负偏差,与Debye-Huckel理论预测的结果相去甚远。工程上使用的Manning模型认为聚离子的电荷密度有一临界值,当超过临界值时,反离子即凝聚在聚离子表面使其实际电荷密度降至临界值。Nagvekar等在该模型的基础上引入NRTL方程,以计及短程相互作用的贡献。Manning等的方法虽然有一定的物理意义,但临界值的确定缺乏可靠的根据。     

Investigation of the Interaction of Sodium Chloride and Two Amino Sulfonic Acids,HEPES and MOPSO,by EMF Measurements

Ionic interactions in the two systems NaCl-HEPES (N-2-hydroxyethylpiperazine-N′-2-ethanesulfonic acid) and NaCl-MOPSO (3-(N-Morpholino)-2-hydroxypropanesulfonic acid) have been studied in terms of their mutual influence on the respective activity coefficients of each component. Activity coefficients for each component of the two systems and for corresponding buffers are calculated from emf measurements of solutions containing NaCl, the aminosulfonic acid, and its conjugate base in a NalSE/solution/AgCl-Ag cell at 5, 15, 25, and 37 °C.     

触摸输入技术探析

本文扼要概述触摸输入的４种技术，及其应用与性能比较。     

Stress in Thin Films;Diffraction Elastic Constants and Grain Interaction

Untextured bulk polycrystals usually possess macroscopically isotropic elastic properties whereas for most thin films transvers isotropy is expected,owing to the limited dimenionlity .The usually applied models for the calculation of elstic constants of polycrystals from single crystal elastic contants(so-called grain interaction models)erroneously predict macroscopic isotropy for an(untextured) thin film.This paper presents a summary of recent work where it has been demonstrated for the first time by X-ray diffraction analysis of stresses in thin films that elastic grain interaction can lead to macroscopically anisotropic behaviour (shown by non-linear sin^2φ plots).A new grain interaction model,predictin the macroscopically anisotropic behaviour of thin films,is proposed.     

激光远距作用的机制与效应

本文定量分析激光远距作用的机理并对它们在治癌中的作用作简要的论述。     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.