Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

连铸喷嘴特性测试与分析

通过测试连铸二冷喷嘴性能，对比同型号喷嘴使用前后两种状态下特性参数，分析了喷嘴参数变化的原因。提出了对使用中的喷嘴特性进行检测与校核的建议，以确保喷嘴特性满足铸坯二冷工艺条件，保证铸坯质量。     

如何控制液压系统的噪声

本文对液压系统噪声产生的原因进行了分析，并相应地介绍了控制液压系统噪声的几项具体措施，指出了在实施噪声控制过程中应注意的事项。     

漏斗贮料压力计算公式

本文从平衡条件和常系数假定出发，建立贮料压力微分方程，导出了正倒锥漏斗、倒锥漏斗贮料压力计算公式。文中说明，圆柱仓筒贮料压力微分方程为上述方程的特殊情形。本文成果可供筒仓工程设计使用，还可供确定斗口给料机贮料荷载参考。     

接触网零件振动试验方法探讨

通过对接触网零件用紧固件的耐振动性能进行振后扭矩测试和横向振动采用压力环测试应变进行对比分析，提出了合理的接触网零件耐振动性能试验方法。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

川中地区上三叠统天然气地球化学特征及成藏过程探讨

川中地区上三叠统是一套自生自储的天然气成藏系统，天然气中甲烷含量为88%～96％，重烃（C2＋）含量一般在6％～9％之间，二氧化碳和硫化氢等非烃气体含量普遍较低；天然气干燥系数（C1／C2＋）为5～15，并且随深度增加而呈现升高的趋势；天然气和凝析油轻烃中的甲基环己烷、庚烷和异庚烷值变化表明天然气主要来源于腐殖型母质；天然气甲烷和乙烷碳同位素分别为-39．00‰～-41．00‰和-25．00‰～-27．00‰，具有典型煤成气特征。川中地区上三叠统烃源岩在燕山期持续沉降埋藏过程中，达到高成熟早期阶段；在喜山期，该地区大约2500m地层的剥蚀，使地层温度和压力大幅度降低，故储层中早期低成熟残余天然气的卸压膨胀作用和水溶气的脱溶作用为晚期天然气聚集成藏提供了重要的气源，同时也使气藏中甲烷碳同位素变轻。     

On the dynamics of non-linear viscoelastic solids with material moduli that depend upon pressure

We investigate the dynamic response, of a generalization of an incompressible Kelvin-Voigt viscoelastic solid, whose viscosity depends on the pressure. Bodies with pressure-dependent material moduli have relevance to numerous technologically significant problems in geomechanics, the mechanics of granular media and powder compaction. We obtain analytical results for creep and recovery phenomena as well as solutions to the propagation of waves in such bodies. We are able to obtain explicit exact solutions that clearly illustrate the marked difference in the response of bodies with pressure-dependent material moduli as opposed to their counterparts whose moduli do not depend on the pressure. We also show that the governing equations for such materials can change type, and that their solutions exhibit singularities and localization.