持续改进求真务实--记宝钢机械厂导入ISO9000质量管理体系标准实绩

简单介绍了宝钢机械厂贯标经验.     

行波管质量与可靠性信息管理系统的设计

本文从应用角度简要介绍了《行波管质量与可靠性信息管理系统》的研制背景，数据库的数据来源，数据结构，系统构成及功能特点。     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

螺杆泵的检测方法及检测标准制定

螺杆泵检测是避免不合格螺杆泵下井、螺杆泵早期失效和提高螺杆泵使用寿命与采油效益的重要技术手段。重点介绍了模拟不同工况的螺杆泵工作特性检测系统及检测定子通径为10－60mm的定子衬套偏心度检测仪的组成及其检测方法和原理。针对大庆油田的实际情况，在进行大量室内和现场试验的基础上，制定了GLB120－27、GLB40－42和GLB500－14型螺杆泵的检测标准。检测技术及其标准实施以来见到了明显效果。     

悬沙中D〉0．06mm粗粒的粒析级配组成及其改正方法

本文首先简述Ｄ＞０．０６ｍｍ泥沙的粒析沉降特性及其粒径偏粗的原因。继之对悬沙中粒径大于０．０６ｍｍ的粒析级配组成机理，及级配组成不同对标准粒径Ｄｂ与粒析粒径ＤＬ关系的影响进行了详细研究。在以上研究工作的基础上，开展了Ｄｂ与ＤＬ的比较试验，得出了粗、中、细型悬沙的Ｄｂ～ＤＬ关系和对ＤＬ的改正方法。     

制革用水乳型聚氨酯涂饰剂行业标准的制定

本文概述了制定该标准的背景，对标准的主要内容加以科学的阐述。     

On basic definitions of unified fracture mechanics terminology

The adoption of unified fracture mechanics terminology (UFMT) will promote efficient communication between specialists in different fields of fracture research, harmonization of national and international standards relating to fracture mechanics, and last but not least improvement of the existing methodology for teaching and education in fatigue and fracture. In this paper the definitions of some basic and related terms included in different standards on fracture mechanics terminology are confronted with one another. Alternative definitions of the same terms are offered. By this strategy the author tries to show that the definitions of basic and related terms appropriate for the UFMT should emerge as a consequence of harmonizing a crack model with an actual crack and then both taken together with a fracture model, laboratory test methods, and failure assessment codes.Published in Problemy Prochonsti, No. 1, pp. 17–29, January, 1996.This paper is published as a matter of discussion.     

材料研究中系列试样的单标样法 X 射线定量分析

本文提出了用一个标样进行系列试样 X 射线定量相分析的方法.它克服了一般 X 射线定量方法需要混合研磨和手续烦复的缺点以及无标样 X 射线定量方法存在病态方程不易解决的问题.该方法对常规 X 射线定量分析具有普遍的实用性.