RBF网络及其在卫星姿态控制中的应用

提出了一种基于RBF网络扰动力矩补偿的控制技术，通过在传统PID控制的基础上，引入RBF网络补偿环节，进一步抑制了扰动力矩的影响，提高了卫星姿态控制精度，首先给出了RBF网络的学习算法，然后根据全补偿原则设计了神经网络补偿姿态控制方案，最后结合某型卫星的姿态控制系统设计实例，进行了数学仿真，结果表明：有RBF网络补偿的系统，姿态的稳态精度得到了明显的改善。     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

The Region 1 & 3 Broadcasting‐Satellite Service Plan after WRC‐03

The 1977 Broadcasting‐Satellite Service (BSS) Plan for Region 1 & 3 had been widely acknowledged to be out‐of‐date by the late 1980s. Development of digital modulation in the early 1990s provided an opportunity to update the technical provisions of the Plan to make it more economically viable. After a decade of work and three World Radiocommunication Conferences (WRCs), the revision of Region 1 & 3 BSS Plan was finally completed in 2003. The new Plan increased channel assignments from 5 to 10 analog‐equivalent channels for each country in Region 1, and from 4 to 12 channels for each country in Region 3. Yet, despite the increase in capacity, the new Plan is surprisingly similar to the original one in terms of the technical parameters. It is still based on national coverage, and the channel plan, orbital location, orbital spacing, and polarization are also the same. As a result, the new Plan is no more economically viable to implement than the old. To create economically viable BSS systems would most likely require modifications to the assignment in the Plan. Yet, modification procedures were made more difficult to apply after replanning. Less future implementation of BSS networks than would otherwise have occurred can be expected, and an inefficient usage of these frequency bands will likely result. On the other hand, less implemented systems will mean more capacity set aside for future use. This is important for countries that currently do not have satellite operations. In the end, BSS replanning reflects the eternal conflict between efficient usage and guaranteed future access. Copyright © 2005 John Wiley & Sons, Ltd.     

激光武器对抗效能指标体系研究

武器系统的效能是规划、研制、配置和部署武器系统的基本依据,是评价武器系统优劣最重要的综合性指标,建立正确的效能指标体系是进行效能分析与评价的前提。在详细研究了激光武器对抗机理、效能指标选用原则的基础上,构建了相对完整的激光武器对抗效能指标体系结构,并提出了在不同作战任务下量度激光武器对抗能力的效能定义。     

Modelling and analysis of 3-D arrangements of particles by point processes with examples of application to biological data obtained by confocal scanning light microscopy

Within the concept of point processes, a review is presented of quantities which can be used in studies of three-dimensional (3-D) aggregates of particles. Suitable characteristics and estimators are given for both unmarked and marked point processes. To demonstrate the feasibility of such quantitative approaches, an application in histology, dealing with 3-D arrangements of cell nuclei in rat liver, is described. Using a confocal scanning light microscope, 3-D images are recorded and image analysis used to obtain the coordinates of the centroid, together with the volume and DNA content, of each cell nucleus. Examples of results are given, using both unmarked and marked point processes. In the latter case, cell type, nuclear volume and ploidy group are suitable marks.     

激光平网雕刻机设计

研制了用于制作平面网版的激光雕刻机，设计了雕刻机用CO2激光器、光路系统及单片机控制系统，探讨了将图像文件转化为控制命令文件的方法。     

采用模数转换技术提高脉冲激光测距的测时精度

针对脉冲激光测距中计数量化误差影响测时精度的问题,本文提出了采用模数转换技术提高测时精度的方法,并进行了可行性与精度分析,理论与实践结果均表明,该方法易于实现,能够容易地将计数量化误差减少若干个数量级。     

激光熔敷合金层组织及腐蚀磨损特性研究

利用ＣＯ＿２连续激光器在４５钢表面进行了激光熔敷镍基合金、镍基Ｃｒ＿２Ｏ＿３合金和镍基ＷＣ合金，以２Ｃｒ１３不锈钢为对比材料，系统地研究了激光熔敷层在不同冲击速度和腐蚀介质浓度下的腐蚀磨损特性，并根据组织分析、显微硬度测试及腐蚀磨损后的表面形貌观察，探讨了激光熔敷层的腐蚀磨损过程。结果表明：激光熔敷层的腐蚀磨损性能均比２Ｃｒ１３不锈钢好。     

不锈钢管子—管板的激光焊接

试验研究了不锈钢的深溶焊接。研究了聚焦光束回转的光具。在工件不动的情况下,焊接管子—管板连接环缝。焊缝质量满足压力容器的要求,焊接效率大大提高。     

光缆CATV用DFB激光器发射组件

介绍了国内首次研制的光缆ＣＡＴＶ用１．３μｍＤＦＢ激光器组件。组件工作频带达到１ＧＨｚ，带内起伏〈１ｄＢ，组件的ＲＩＮ〈－１５３ｄＢ／Ｈｚ；出纤光功率〉２ｍＷ，载噪比ＣＮＲ〉５０ｄＢ。首次实现用低反射尖锥端光纤的ＤＦＢ激光器耦合。