Efficacy of alpha-cypermethrin and thiamethoxam against Trogoderma granarium Everts (Coleoptera: Dermestidae) and Tenebrio molitor L. (Coleoptera: Tenebrionidae) on concrete

Laboratory bioassays were conducted to evaluate alpha-cypermethrin and thiamethoxam for the control of adults, small larvae and large larvae of the khapra beetle Trogoderma granarium, and the yellow mealworm beetle Tenebrio molitor, on concrete. Factors such as dose (0.025 and 0.1 mg alpha-cypermethrin or thiamethoxam/cm²), exposure interval (1, 3 and 7 d), and formulation (alpha-cypermethrin SC and thiamethoxam WG) were evaluated. Apart from immediate assessment at end of exposure, an assessment of delayed mortality was performed with the survivors of the 7-d exposure by removing them from the treated substrate and keeping them on untreated surfaces for 7 more days. After the 7-d exposure, more T. granarium adults were dead on dishes treated with alpha-cypermethrin than with thiamethoxam. Small larvae were generally less susceptible than adults. After 7 d, small larval mortality reached 64.4% for alpha-cypermethrin, while for thiamethoxam it was <6%. Large T. granarium larvae were more tolerant than the small ones. Delayed mortality of T. granarium adults was generally high for both insecticides and doses, and ranged between 43.3 and 63.3% of those that were still alive immediately after the 7-d treatment. For both larval categories, delayed mortality was higher for larvae that had been previously exposed to alpha-cypermethrin, than with thiamethoxam. For T. molitor, after the 7-d exposure, significantly more adults were dead on dishes treated with alpha-cypermethrin than with thiamethoxam. For small larvae mortality was 38.9% at the lowest thiamethoxam dose, but in the other cases ranged between 88.9 and 95.6%. In the case of large larvae, the overall mortality was low in all tested combinations. Regarding delayed mortality of this species, it remained at low levels, for both adults and small larvae. Our results indicate that T. molitor was more susceptible than T. granarium in both insecticides tested, but alpha-cypermethrin was more effective than thiamethoxam.     

Seawater-softening process through formation of calcite ooids

Conventional water-softening processes usually involve the exchange of Na⁺ ions for Ca²⁺ and Mg²⁺ using commercial or synthesized ion exchangers. The differences in chemical compositions of the ooids can be attributed to the formation in different environments. In this paper, ooid grains form inside assembled semi-pilot softening unit through a continuous chemical process involving reaction between bicarbonate ions and added lime using natural seawater. Our sample of Mediterranean seawater has low Mg²⁺/Ca²⁺ ratio (1.98%) within the range chemically favorable for precipitation of low-Mg calcite ooids. Precipitation of calcite occurs around pure quartz sand grains which act as nucleation points (the bed required for sand vessel is 1.65 l). The shape of the sand grains controls the overall external morphology of the resulting ooids; they vary in size from 0.5 to 3.0 mm and have a high degree of polish due to surface abrasion caused by continuous agitation inside the softening system. Calcite ooid grains (1.53 kg) formed within the seawater-softening unit every 18 days have many of the ooid features formed in marine environments. Ooids grow to a significant size, at a rate of about 0.17 mm of one layer thickness per day inside the softening unit. The average weight percent of calcite precipitate is 35.48% after 18 days, at 10 °C, 60 l/min and pH 9.0. The pellets comprise mainly CaCO₃ and SiO₂ and some metal ions which may substitute for calcium ions in calcite are present only in trace amounts of the total composition.     

Improvement of adhesion and paint ability of EVA copolymers with different vinyl acetate contents by treatment with UV-ozone

The surface modifications produced by UV-ozone treatment of two ethylene-vinyl acetate (EVA) copolymers containing 12 and 20 wt% vinyl acetate (EVA12 and EVA20 respectively) were studied. The treatment with UV-ozone improved the wettability of both EVAs due to the creation of new carbon–oxygen moieties. The extent of these modifications increased with increasing length of the treatment and the modifications produced in EVA20 were produced for shorter lengths of treatment. The UV-ozone treatment also created roughness and heterogeneities on the EVA surfaces. Whereas roughness formation prevailed on the UV-ozone treated EVA12, important ablation was dominant on the treated EVA20. T-peel strength values in joints made with polychloroprene adhesive increased when the EVAs were treated with UV-ozone. Short length of UV-ozone treatment (1 min) produced higher T-peel strength in joints made with EVA20 whereas higher T-peel strength values in joints made with EVA12 were obtained after treatment for 5–7.5 min in which a cohesive failure into a weak boundary layer on the treated EVA surface was found. Furthermore, the adhesion of UV-ozone treated EVA20 to acrylic paint increased. Finally, the ageing resistance of the treated EVA/polychloroprene adhesive joints was good and the surface modifications on the UV-ozone treated EVAs lasted for 24 h after treatment at least.     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

玄武岩纤维填料应用于两种混合生长反应器的评价

采用单丝直径微米级的伞状玄武岩纤维(BF)作为填料,将其引入序批式反应器(SBR)和后置缺氧反硝化SBR外聚合物(EPS)含量和扫描电子显微镜形貌图,考察了两种SHBR的污水处理效果。试验结果表明:基于SBR的SHBR的出水COD、氨氮、总氮去除率分别为83.2%、89.9%、86.8%;基于后置缺氧反硝化SBR的SHBR优良,而基于后置缺氧反硝化SBR的SHBR的脱氮效果得到进一步的优化和提升。两种SHBR的BF填料中EPS含量分析结果显示:在好氧环境下,蛋白质(PN)的含量高于多糖(PS)的含量;在缺氧条件下,PS的含量明显高于PN的含量。     

Hydrogenation process in multiphase alloys of Ti-Zr-Mn-V system on the example of Ti42.75Zr27Mn20.25V10 alloy

The influence of phase composition and microstructure of Ti_42.75Zr₂₇Mn_20.25V₁₀ alloy on its hydrogenation kinetic and phase composition of hydrogenated product was studied. It is established that the process of dissociation of hydrogen molecules begins on the surface of Laves phase crystallites. The dissolution of atomic hydrogen in the material volume leads to the formation of cracks in the intermetallic crystallites, which further appear as additional centers of dissociation of hydrogen molecules and noticeably accelerate the diffusion of hydrogen into the bulk material. It was shown that the Laves phase acts as a donor of atomic hydrogen for the BCC solid solution during hydrogenation of two-phase structure, initiating intensive hydrogenation of the BCC phase at room temperature.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

Simulation Analysis of the Heat Transfer Performance of an N-type Microchannel Heat Exchanger

A microchannel heat exchanger with a triangular wave and symmetrical triangular wave structure was proposed in this paper. In addition, a new N-type microchannel heat exchanger was developed to balance the heat transfer performance and pressure drop. The relationship between different configurations of the N structure of the microchannel and the heat transfer performance was analyzed. The results showed that, at a high inlet flow rate, the symmetrical triangular wave microchannel had the best heat transfer performance, followed by the triangular wave microchannel and the straight channel. At the same flow rate, the degree of disturbance of the fluid was highest in the symmetrical N-structure microchannel, and an excellent heat transfer effect was observed.     

Biological Water Treatment by a Hybrid Fluidized-Bed Bioreactor: Theoretical Study

A hybrid fluidized-bed bioreactor for water purification was proposed and analyzed. It is a novel type of bioreactor characterized by hitherto unknown stationary and dynamic features. Steady-state characteristics of this hybrid bioreactor with external liquid circulation are presented. A quantitative analysis of steady-state properties of the bioreactor was performed with the aid of an original mathematical model developed for a double-substrate aerobic microbiological process. A steady-state analysis of aerobic processes characterized by different oxygen demand was performed. The effect of essential parameters was evaluated, including carbonaceous substrate concentration in the feed stream to the apparatus, aeration intensity, total residence time of a liquid in the bioreactor, and height of the bed of fine carrier particles.