未脱墨废人民币纸浆配抄瓦楞原纸

为增加造纸工业的纤维原料来源并充分利用废人民币纸,本文对未脱墨废人民币纸浆配抄瓦楞原纸进行了初步的研究。采用5%氢氧化钠和硫酸溶液对废人民币纸进行化学预处理,再经PFI磨机械疏解后得到未脱墨的废人民币纸浆。采用纤维形态分析仪对未脱墨废人民币纸浆的纤维长度、宽度及其分布进行了分析检测。通过在废新闻纸浆中配加不同比例的未脱墨废人民币纸浆考查瓦楞原纸的质量指标,并对不同的纸浆配比进行分析。结果表明,废人民币纸浆的纤维长度在机械疏解过程中损失较多,只相当于草类原料化学浆的纤维长度。抄造定量为120 g/m2的瓦楞原纸,当废人民币纸浆配比增加时,瓦楞原纸的裂断长和环压指数均下降,废人民币纸浆的配抄比例控制在40%左右时,可以满足D级瓦楞原纸对裂断长和环压指数的要求。虽然废人民币纸浆的成纸强度较低而导致瓦楞原纸的强度指标下降,然而由于其原料价格较低,有利于降低瓦楞原纸的生产成本。     

Comparison of TiAIN,AICrN, and AICrN/TiAIN coatings for cutting-tool applications

Monolayer and bilayer coatings of TiAlN, AlCrN, and AlCrN/TiAlN were deposited onto tungsten carbide inserts using the plasma enhanced physical vapor deposition process. The microstructures of the coatings were characterized using scanning electron microscopy （SEM） and atomic force microscopy （AFM）. The SEM micrographs revealed that the AlrN and AlCrN/TiAlN coatings were uniform and highly dense and contained only a limited number of microvoids. The TiAIN coating was non-uniform and highly porous and contained more micro droplets. The hardness and scratch resistance of the specimens were measured using a nanoindentation tester and scratch tester, respectively. Different phases formed in the coatings were analyzed by X-ray diffraction （XRD）. The AlCrN/TiAlN coating exhibited a higher hardness （32.75 GPa）, a higher Young＇s modulus （561.97 GPa）, and superior scratch resistance （LcN = 46 N） compared to conventional coatings such as TiAlN, A1CrN, and TiN.     

Reasonable location parameters of pick and nozzle in combined cutting system简

The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order to solve the problem, the process and mechanism of combined cutting arc studied and mining seepage catastrophe theory is used to construct the mathematic and physical model of combined cutting hard coal-rock. Based on the model and detailed analysis of combined cutting mechanism, the single pick and nozzle combined cutting test-bed is built to test the main pick and nozzle location parameters of drum shearer and water jet combined cutting system. Test results show that the best vertical distance between the pick-tip and nozzle center point is the sum of cutting thickness and proper target distance in the Y axial direction; the best horizontal distance is the length between pick-tip point and coal-rock surface bursting crack point in the X axial direction. The best incident angle of water jet should be the same as the bursting crack line＇s angle in theory, but considering other important factors comprehensively, it is more reasonable when the incident angle of water jet is 90°.     

环形刀高度变化刀路轨迹规划方法

为提高汽车覆盖件模具加工效率,将环形刀应用于汽车模具小曲率面的半精及精加工过程.通过对三坐标铣削小曲率面的刀具切触几何分析,确定环形刀最佳进给方向应沿工件高度变化方向,此时可使有效切削带宽达到最大.基于此结论,分别对两类特殊型面进行了刀路轨迹规划.对于单一方向曲率变化面采用垂直截面法,截面方向沿最大主曲率方向,实验表明:垂直截面法与等高线法相比可提高加工效率25%,并且有较好的表面质量;对于圆鼓面采用放射精加工方法,仿真结果表明:此方法与三维偏置方法相比可提高加工效率22.64%,并且避免了周边欠切.     

刀具几何角度对高速铣削性能影响的仿真分析

切削力和切削温度是影响刀具耐用度及被加工表面质量的重要因素,其中刀具几何角度在金属切削加工过程中对切屑的形成、切削力的大小以及散热条件等影响很大。因此,合理地选择刀具几何角度对提高刀具使用寿命和生产效率、降低生产成本具有重要意义。以铝合金7075-T651高速铣削为研究对象,借助金属切削工艺软件AdvantEdge对铣削加工进行模拟仿真,得到加工过程中切削力和温度随时间的变化关系,并结合单因素法,分析了不同刀具角度的选择对切削力和切削温度的影响。该结果为高速铣削刀具几何角度的选择提供参考。     

难加工材料细长薄板件的加工

针对难加工材料细长薄板零件的加工特点,设计了这类零件加工的刨削加工工艺方案,探讨了刨削加工方法在细长薄板零件加工中的应用.     

智能井用管线切割工具设计

采用智能完井技术的油井,修井周期长,长年生产的井中积累较多的油垢、胶质等杂物,修井时起出管柱较为困难。在管柱起出遇卡时,常规的切割工具只能对油管进行切割,无法对井下工具的控制管线进行切割。设计了一种专用的管线切割工具。介绍了该工具的结构、工作原理、技术参数、施工工艺。分析了关键结构的强度。通过ANSYS软件对管线剪切模型进行有限元分析,结果表明管线切割工具可承受拉力达800 kN,可对6根不同尺寸多种组合的控制管线进行切割。进行下部管柱打捞过程中,不会有冗杂的管线阻碍打捞作业。     

深井裸眼封隔器分段酸压管柱打捞实践

安岳气田灯影组气藏广泛采用大斜度井/水平井裸眼封隔器分段酸压工艺试油完井,悬挂封隔器及下部管柱被“永久性”留在井下。如果利用原裸眼侧钻,则需要打捞分段酸压管柱至套管鞋以下30 m左右。MX126井和GS121井前期打捞作业历时均超过50 d,打捞效率非常低,主要原因为：悬挂封隔器双向锚定,裸眼封隔器和连接油管埋卡严重且位于大斜度井段,压井后长时间静止埋卡越来越严重;钻井液压井后切割油管受阻,没有完成落鱼切割分段;套磨铣导致封隔器解体,倒扣时落鱼出现多处退扣,倒扣打捞效率低。针对上述问题,优化了打捞技术措施：钻井液压井前,采用泵送径向切割工艺在清水中切割油管,确保切割成功率;采用带压拔出插管循环压井,缩短钻井液浸泡时间,降低次生卡钻风险;优选磨铣工具和打捞工具,优化磨铣工艺和震击解卡打捞工艺,维持落鱼完整性、力求捞出整段被切割落鱼。该技术成功应用于MX146井和GS127井后期的打捞作业,分别用时12 d和5 d。该技术可以显著提高裸眼封隔器分段酸压管柱的打捞效率,具有推广应用价值。     

Reinforcing effect of nanocrystalline cellulose and office waste paper fibers on mechanical and thermal properties of poly (lactic acid) composites

Nanocrystalline cellulose (NCC) was prepared from office waste paper (OWP) by sulfuric acid hydrolysis method in this paper and it was used to prepare a series of poly (lactic acid) PLA/NCC composites by using a dissolution method in solvent N, N-dimethylformamide solution. The results indicated that with the addition of only 3 wt% NCC, the composites exhibited outstanding mechanical property. The tensile, bending and impact properties of the PLA/3NCC composite were improved by 8.2%, 13.1%, and 35.9% than those of pure PLA, respectively. On this basis, office waste paper fibers (OWF) were also used as a physical blended filler to enhance PLA/NCC composites to reduce the preparation cost of PLA composites and the perfect PLA/NCC/OWF sample was easily manufactured by melting–blending and injection molding. According to the crystallization and melting performance table, both NCC and OWF can act as nucleating agent to promote the crystallization properties on composites, while the blends did not have positive effect on thermal stability. Furthermore, the water absorption and degradation properties of PLA composites were also studied. This work not only provided a novel idea for the utilization of office waste paper but also successfully produced environment friendly composites with favorable mechanical properties and crystallization performance.     

Machinability of a nickel aluminide intermetallic alloy

This article reports the results of an experimental study on the machinability of a nickel aluminide intermetallic alloy. Machining was conducted at various speeds, and results indicate low material removal rates. Chips collected for each test run were measured for thickness for shear angle calculation and were subsequently observed microscopically. Chip segmentation was observed microscopically, and a fluctuation in the shear angle was evidenced. A parameter characterizing the severity of the machining process, the chip reduction coefficient (K), was calculated from chip thickness measurements. The calculated values ofK were found to be low, indicating a low severity of the metalcutting process. This, however, is in contract with the observed low rates of metal removal and low tool life. Thus, conventional metalcutting characterization parameters require re- examination in terms of machining high-strength materials.