CuO-NiO/Al_20_2催化剂上N-甲基哌嗪合成研究

以共沉淀法制备铜、铝系复合氧化物作为催化剂,二乙醇胺和甲胺为原料,合成了N-甲基哌嗪.利用高压反应釜对其进行活性评价,发现CuO-NiO/Al2O3活性最高.并对铜、铝、镍摩尔比、沉淀剂种类、沉淀方式,焙烧温度等条件进行了优化.结果表明:催化剂中理想的Cu、Al、Ni摩尔比为1:1:3.2,沉淀剂为氢氧化钠,沉淀方式为并流,焙烧温度为500℃.该条件下N-甲基哌嗪的选择性为27.7%,二乙醇胺的转化率达89.8%.另外通过对使用前后催化剂进行表征分析发现催化剂失活原因为表面高聚物的附着和对孔道的堵塞.     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

高温预析出对Al-Zn-Mg-Cu铝合金显微组织、强度和应力腐蚀抗力的影响

通过改变固溶条件 ,对Al Zn Mg Cu高强铝合金采用先高温后低温的两步固溶处理 (高温预析出 )来改善晶内和晶界的析出状态 ,研究了高温预析出对Al Zn Mg Cu铝合金的金相组织、强度和应力腐蚀性能的影响。结果表明 ,4 6 5℃高温预析出在保持较高强度和塑性的同时 ,可以改善合金的抗应力腐蚀性能     

Thermophysical properties of a Ti–44%Al–8%Nb–1%B alloy in the solid and molten states

The families of titanium aluminide intermetallic alloys have attractive high temperature mechanical properties which make them potential candidate materials for a wide range of applications, particularly in the aeronautic and automobile sectors. The development of appropriate manufacturing techniques is an essential stage in the engineering exploitation of these materials, e.g., Induction Skull Melting is one of the techniques which needs to be optimised for the casting of titanium aluminides. Research is underway to develop a computer model of this process but data are required for the key thermophysical properties. Pulse-heating techniques have been used to measure properties for the Ti–44Al–8Nb–1B system. Rectangular samples have been prepared and are resistively heated as part of a fast capacitor discharge circuit. Time-resolved measurements with sub-μs resolution of currents through the specimen were made with a Pearson probe current monitor using the induction principle. Voltages across the specimen were determined with knife-edge contacts and voltage dividers, and radiance temperatures of the sample were measured with a pyrometer. These measurements allow the calculation of specific heat and dependencies between enthalpy, electrical resistivity and temperature of the alloy up into the liquid phase. Data for thermal diffusivity have been obtained by using the Wiedeman–Franz relation. The results are compared with those obtained using DSC and the four-probe method to measure the temperature dependence of the resistivity.     

Effect of Al in Ti－microalloyed Mn－Ni－Mo welding wire on microstructure and toughness of deposited metal

ＥｆｆｅｃｔｏｆＡｌｉｎＴｉ－ｍｉｃｒｏａｌｌｏｙｅｄＭｎ－Ｎｉ－Ｍｏｗｅｌｄｉｎｇｗｉｒｅｏｎｍｉｃｒｏｓｔｒｕｃｔｕｒｅａｎｄｔｏｕｇｈｎｅｓｓｏｆｄｅｐｏｓｉｔｅｄｍｅｔａｌ￥ＴａｎＣｈａｎｇｙｉｎｇ；ＺｈａｎｇＸｉａｎｈｕｉａｎｄＳｕｎＷｅｉ...     

TiCp/Al预制块在Mg中熔化过程研究

将TiCp／Al预制块以不同的工艺加入到Mg液中进行熔化试验。结果表明，未搅拌时TiCp／Al预制块在800℃的Mg液中保温60min后仍不熔化，采用合适的搅拌工艺可使TiCp／Al预制块熔化，并且使TiC粒子在熔体中均匀分布。TiCp／Al预制块在Mg液中的熔化过程机理为：基体Al通过熔化和对淹扩散进入到Mg液中，TiC粒子间的结合力需通过搅拌产生的剪切力才能破坏，并随Mg液流动进入到Mg液中，机械搅拌可使TiC粒子Mg液中均匀分布。     

Anti-oxidation mechanism of SiC-B4C-C composites

Mixture of green petroleum coke, B4 C and SiC together with short carbon fiber were employed as starting materials, the mixture was press formed without any binder after grinding, dense and homogeneous binderless SiC-B4 C-C（carbon/ceramic） composites were then obtained after sintering. Composites thus prepared possess excellent anti-oxidation property, that is, mass loss less than IG within the temperature range from 900 to 1 100 ℃ for 10 h. Anti-oxidation mechanism was also discussed from the viewpoint of thermodynamics, excellent anti-oxidation property of materials thus prepared can be discribed to 1） solid SiO2 formed from SiC, which restrains the filtering of oxygen and simultaneously, its volume expansion brought about by the reaction takes roles both walling up the original pores and making the material more compact; 2） liquid B2O3 from the reaction of B4C not only makes the combination with C, B4 C and SiC tighter through forming solid solution, but also effect of reaction SiC（s）＋2CO（g） =SiO2 （s）＋3C（s） is an expansive process, which improves the microstructure of the material.     

Influence of Reinforcement Content and Matrix Composition on the Oxidation Resistance of Aluminum-Matrix Composites (A3xx.x/SiCp)

A study was made on the influence of the SiCp proportion and the matrix concentration of four composites (A360/SiC/10p, A360/SiC/20p, A380/SiC/10p, A380/SiC/20p) on their oxidation behavior. Gravimetric tests were used in a kinetics study of the corrosion process at different temperatures (350, 400, 450, and 500°C). The influence of corrosion on mechanical properties was evaluated by hardness measurements. The nature of corrosion products and the influence of the microstructure on the morphology and growth of the oxidation layer were analyzed by SEM and low-angle XRD. The extent of the damage due to oxidation for Al/SiCp composites increases with the SiCp concentration due to the increase of nucleation sites. One of these nucleation sites is in the interface region between the matrix and the particles. Oxidation was influenced more by the percentage of alloy elements in the matrix than by the proportion of SiCp reinforcement. The presence of Cu and Ni in the matrix favors the oxidation process through the formation of different intermetallic compounds.