电力信息自动化系统中Web技术时间应用分析

在我国的变电所的分布不是非常集中,并且变电的设备也较多,因此精确管理难度和宏观调度都有很大的增加。WEB技术可以使得非常简单的浏览和开发信息,并且可以使得变电所之间的信息交流便得增加,因此电力信息自动化系统的WEB技术应用越来越广泛。     

区位码/国标码输入法技术初探

计算机技术领域中,使用键盘输入汉字的方法实质是区位码/国标码输入法。本文介绍了区位码/国标码输入法的现实意义,IME的组成结构以及区位码/国标码输入法的发展动态。主要说明区位码/国标码输入法在中文键盘输入法的重要地位,并简单分析了中文键盘输入法编辑器的组成结构等技术。     

基于LabVIEW的高温超导脉冲功率状态监控系统

脉冲功率数据采集系统是确保脉冲功率系统稳定安全运行的关键之一,超导脉冲功率系统由超导储能系统和外部放电电路组成。本文设计了基于LabVIEW的超导脉冲功率状态监控系统,该系统由多路传感器、信号调理电路和高精度数据采集系统构成,实现了对超导脉冲功率系统各个数据的精确采集,并利用虚拟仪器强大的数据处理能力,实现了对超导脉冲功率系统运行状态的准确判断,实验结果表明设计的状态监控系统能够有效地监控高温超导脉冲功率系统的运行状态。     

LFM信号限幅失真对侧扫声纳声图的影响

本文分情况讨论了LFM信号限幅失真对脉冲压缩及侧扫声图的影响并进行了湖试验证。结果表明:限幅失真对于脉压波形的主瓣几乎没有影响,即不会影响到声图的分辨率,但是会使脉压波形的幅度产生失真。当限幅程度较大时,由于信号的叠加会进一步恶化脉压波形,使脉压信号的幅度明显降低,甚至产生假目标,信号的动态变化范围被严重压缩;即使当单个信号不限幅时,而由于多目标回波相互叠加也可能会引起信号限幅,此时也可能对处理结果造成较为严重的失真,使信号动态范围被压缩。     

Thermal expansion of molybdenum in the range 1500–2800 K by a transient interferometric technique

The linear thermal expansion of molybdenum has been measured in the temperature range 1500–2800 K by means of a transient (subsecond) interferometric technique. The molybdenum selected for these measurements was the Standard Reference Material SRM 781 (a high-temperature enthalpy and heat capacity standard). The results are expressed by the relation where T is in K and l ₀ is the specimen length at 20°C. The maximum error in the reported values of thermal expansion is estimated to be about 1% at 2000 K and not more than 2% at 2800 K.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

Aluminum. II. Derivation of C v0from C p and comparison to C v0 calculated from anharmonic models

The specific heat at constant pressure, C _p, of aluminum measured by Ditmars, Plint, and Shukla has been reduced to the volume V ₀ appropriate for 0 K employing the Murnaghan equation. The C _v0 thus obtained is compared with the theoretical C _v0 calculated in the harmonic and the lowest-order anharmonic approximation from three different pseudopotentials (Harrison, Ashcroft, and Dagens-Rasolt-Taylor) as well as a phenomenological Morse potential. The higher-order ( ⁴) anharmonic contributions are calculated from the same nearest-neighbor Morse potential as in the lowest-order anharmonic theory. The role of the vacancy and the higher-order anharmonic contributions to C _v0 has been examined and we conclude that the ⁴ contributions to C _v0 are much smaller than the vacancy contribution. After removal of the vacancy contribution, the reduced C _v0 is found to be in excellent agreement with the Ashcroft and Harrison pseudopotentials as well as the Morse potential including the ² and ⁴ contributions to C _v0.     

电流密度对声电沉积生物活性透钙磷石涂层结构和形貌的影响

通过声电沉积工艺在碳／碳复合材料表面制备了生物活性透钙磷石涂层，采用SEM、FFIR、XRD研究了超声场中电流密度对涂层组成结构和形貌的影响。发现在一定工艺条件下，随电流密度增加，涂层的平均晶粒尺寸减小，致密度增加；当电流密度小于l0mA／cm^2时涂层形貌为片状，l0mA／cm^2-26mA／cm^2时为粒状，32mA／cm^2时为花菜心状。且涂层中透钙磷石晶体的择优取向也发生变化，择优晶面依次为(021)、(111)、(220)。同时还讨论了涂层微观结构变化机理。     

分流挤压镁合金管材工艺研究

用分流挤压方法可生产挤压比不大于68，壁厚不小于1．5mm的非薄壁镁合金管材，其表面基本上无烧损、无横裂纹等缺陷。主要工艺参数：挤压筒温度250-350℃，镁棒温度320-380℃，模具预热温度300-380℃。模具及其内残余镁合金重复加热可保证模具多次使用，不用清洗。     

国外钢管产品结构分析(上)

介绍了日本、美国、韩国、前苏联等国家不同时期各种钢管产品结构的发展情况及构成比。分析了影响钢管比、焊管比、特殊钢管比、冷加工管比和覆层管比的主要因素。指出了今后的发展趋势。