(1-x)NBT-xBaTiO3系陶瓷材料制备过程中烧成工艺制度的研究

选取BT6组成点,采用不同的预合成温度、烧结温度和保温时间制备样品,研究各样品的体积密度、线收缩率、晶粒发育状况和压电性能,确定最佳的烧成工艺制度。     

Preparation and characterization of multi-walled carbon nanotubes supported PtRu catalysts for proton exchange membrane fuel cells

A series of PtRu nanocomposites supported on H₂O₂-oxidized multi-walled carbon nanotubes (MWCNTs) were synthesized via two chemical reduction methods—one used aqueous formaldehyde (HCHO method) and the other used ethylene glycol (EG method) as the reducing agents. The effects of the solvents (water and ethylene glycol) and the surface composition of the MWCNTs on the deposition and the dispersion of the metal particles were investigated using N₂ adsorption, TEM, ICP-AES, FTIR and TPD. The wetting heats of the MWCNTs in corresponding solvents were also measured. The characterizations suggest that combination of the surface chemistry of the MWCNTs with the solvents decides the deposition and the dispersion of the metal nanoparticles. These nanocomposites were evaluated as proton exchange membrane fuel cell anode catalysts for oxidation of 50 ppm CO contaminated hydrogen and compared with a commercial PtRu/C catalyst. The data reveal superior performances for the nanocomposites prepared by the EG method to those by the HCHO method and even to that for the commercial analogue. Structure–performance relationship of the nanocomposites was also studied.     

浸入式水口燃烧式烘烤预热温度场研究

浸入式水口在浇钢以前必须进行充分预热 ,利用燃烧的煤气烘烤水口是常用的预热烘烤方式。本工作运用有限元技术对浸入式水口燃烧式烘烤预热的瞬态传热过程进行了研究 ,得到了水口烘烤预热后的温度场分布和水口的升温曲线。研究结果表明 ,在燃烧式预热烘烤方式下 ,水口沿轴线方向的温度变化梯度较大 ,水口颈部预热后的温度较低 ,是导致水口颈部频繁断裂和较易出现竹节样裂纹的主要原因。欲提高水口颈部的预热温度 ,必须改进水口的预热烘烤方式     

间歇窑窑墙温度场图形仿真研究

本文利用有限差分法求解间歇窑窑墙中的温度分布，并用Ｃ语言设计了窑墙温度场图形仿真软件。输入窑墙厚度和材料的物性参数等，系统可进行窑墙温度场分布的实时仿真及窑炉结构与操作的优化     

Anodic dissolution of spongy titanium in ethanol solution for preparation of nano-sized TiO2 powder

Nano-sized TiO₂ powder was prepared by electrochemical dissolution of spongy titanium in an ethanol solution following direct hydrolysis of the electrolyte solution. Characterization of the electrochemical product revealed that Ti(OEt)₄ was formed by anodic dissolution of spongy titanium in ethanol solution. X-ray diffraction and transmission electron microscope were, respectively, used to investigate the structure of TiO₂. This study showed that nano-sized TiO₂ prepared by this method has a structural and thermal stability with a narrow size distribution of 5-10 nm. The optimum electrochemical operating conditions established were a temperature of 333-343 K, current density of 400 A m⁻² and faradaic efficiency of 86%. Experiments showed that this process might be recommended as a promising technique for synthesis of nano-sized powder.     

集成于无源UHF RFID标签的宽温测范围CMOS温度传感器

针对无源UHF RFID标签温度测量范围小、功耗等问题,本文提出了一种集成于无源UHF RFID标签的宽温测范围CMOS温度传感器。本文设计采用UMC 0.18μm 1P6M CMOS工艺进行设计,提出一种新温度脉冲转换电路结构产生随温度变化的脉冲,从而实现了宽温度测量。仿真结果表明:当温度范围在-75℃~125℃时,温度脉冲宽度变化近220μs,标签芯片供电电压为1.5V时,室温时新增的温度传感器模块功耗仅为200 nW,温度传感器精度为0.45℃/LSB。测试结果:在-5℃~45℃范围内进行测试,温度传感器精度为0.48℃/LSB,其中在室温25℃左右振荡器频率2.087 MHz,脉冲宽度大约110μs,异步计数器显示为011011000。     

陶瓷磨光弧面板的开发与应用

研究了陶瓷板材在各种温度及压力下产生的应力、应变与板材断裂之间的关系和规律,提出了陶瓷板材的弯曲方法,研制各种专用试验、生产设备,将成品陶瓷平板加工成为园柱板、弧面、球面、圆锥面、双曲面等各种曲面板.     

Moisture adsorption characteristics of a thin bed of polycrystalline potash pellets: Part I. Experimental study

This study is an experimental investigation of heat and moisture transfer within a packed bed of polycrystalline, porous potash pellets. Experiments were first performed to determine the moisture uptake characteristics on individual pellets subject to a step-change in relative humidity. Then a bed of pellets was subjected to flows of humid air on the upper boundary and a cold impermeable surface on the lower boundary resulting in a temperature gradient across the bed. Temperature and moisture content were measured within the bed. It was found that moisture uptake is less for potash pellets and they are less likely to cake than granular and standard potash when subjected to the same ambient air conditions. This is due to the porous nature of the pellet and its nearly uniform size and spherical shape.     

裂解气压缩机级间注水技术的应用

介绍了裂解气压缩机由注洗油改为注水情况，进而得出结论：改注水降温效果明显，压缩机工作效能可得到有效保障。