砾岩油藏合理注采压力系统研究--以七中东区八道湾组油藏为例

注采压力系统指的是从注水泵站到采油井井口的各环节的压力配置 ,在这一压力系统中 ,地层压力和油井流动压力是决定整个压力系统的关健 ,也是油藏工程研究的核心。本文利用油藏工程方法对砾岩油藏高含水期油井和注水井的地层压力、流动压力等注采压力系统进行了研究界定 ,将为砾岩油藏的开发水平提供技术支持     

纳米ZnO薄膜制备及液态源掺杂

用真空蒸发法在玻璃和单晶硅片 (10 0 )上制备Zn薄膜 ,然后对Zn薄膜进行氧化、热处理获得纳米ZnO薄膜。对在硅片上制备的Zn薄膜一次性进行高温掺杂、氧化获得纳米ZnO∶P和ZnO∶B薄膜。研究不同氧化、掺杂温度和时间对薄膜结构、电学性能的影响。结果表明 :氧化温度和时间对ZnO薄膜结构影响较大 ,液态源掺P可明显改善纳米ZnO薄膜的导电性能、结构特性和化学组分     

Drying of Probiotics: Optimization of Formulation and Process to Enhance Storage Survival

This work describes how probiotic bacteria can be dried at low temperature in two steps, combining spray drying and vacuum drying, in order to enhance their survival during storage. A sufficient number of dried probiotics survived storage for more than 3 months at 30°C, if an appropriate combination of protein and carbohydrate was selected as carrier and storage conditions were maintained optimal. The use of soy protein and maltodextrin or skim milk and arabic gum resulted in the best survival rates of probiotics during storage. No evident difference was found between different spray dryer configurations, although a cocurrent flow was preferred.     

微密封真空微电子二极管

本文介绍了一种微密封真空微电子二极管的工艺及实验结果。     

集成pH－ISFET／压力传感器的研究

基于ＳＤＢ／ＳＯＩ材料和硅微机械加工技术，提出了一种含微参比电极和择优差分补偿单元的背面引线ＰＨ－ＩＳＦＥＴ／压力传感器的新结构。并且设计了高稳定的可调芯片自恒温系统，以减少硅材料对温度敏感的效应。这种结构既方便地实现敏感元和信号处理电路的完全隔离，又有效地改善了敏感特性和稳定性。初步实验结果证实了新结构设计是成功的。     

Optimizing the Vacuum Heat-Treatment of Hot-Work Tool Steels by Linear Elastic Fracture Mechanics

Linear elastic fracture mechanics was used to optimize the vacuum heat-treatment procedures for conventional hot-work AISI H11 tool steel. The fracture toughness was determined with non-standard, circumferentially notched and fatigue-precracked tensile-test specimens. The fracture-testing method is sensitive to changes caused by variations in the microstructure resulting from the austenitizing and tempering temperatures as well as the homogeneity of the material itself. The combined tempering diagram- Rockwell-C hardness, Fracture toughness K_Ic, Tempering temperature was used for the choice of the vacuum heat-treatment parameters necessary to obtain the best properties for a given application with respect to the investigated steel.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

大庆油田助剂厂3500kt／a常减压减压塔的管道设计

简述了大庆油田助剂厂3500kt/a常减压减压塔的管道布置设计特点,体现出塔类设备的管道设计原则,并结合管道设计的经济性、安全性展开论述。     

VFD GU384x32L-3900模块特性及应用

GU384x32L-3900是一款内藏驱动电路的、384×32点阵式VFD显示模块。介绍了GU384x32L-3900模块的基本结构及软件编程、硬件应用等特性并探讨了其在实际中的应用。