Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

Optimal size,hydraulic retention time and volatile solids loading rate of biogas unit using water hyacinth

With a view to evaluate the effects of hydraulic retention time and volatile solids loading rate on methane production using water hyacinth, experiments were conducted in a 160 dm³ capacity, well-mixed continuous digestion unit at ambient temperature. The optimal design of biogas plant using water hyacinth was elucidated, to provide a unit giving a maximum methane yield of 0.16 nm³ kg^?1 volatile solids added, which was 60% greater than the conventional plant using cowdung. The calculations of optimal design factors were based on reactor size, hydraulic retention time and volatile solids loading rate; considerations were made of capital cost, running costs and operational revenue.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

基于加载算法的室内无线信道OFDM接收机的性能

本文研究了无线局域网中使信号频谱得到优化的一种简单OFDM子载波加载算法。此算法基于边缘自适应（Margin Adaptive）加载准则及其在室内无线信道上的性能。     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

The effect of welded boundaries on the response of rectangular hot-rolled mild steel plates subjected to localised blast loading

A series of experiments examining the effects of welded boundaries on the localised blast load response of mild steel plates is presented in this short communication. Two types of welding are examined, TIG and MIG welding. The welded boundary response is compared with clamped boundary and straight and chamfer machined boundary responses. The overall trend of midpoint deflection–thickness ratio versus dimensionless damage number for all the plates follows previously reported empirical trends. The tearing threshold (Mode II*) in terms of the damage number is lowest for the machined plates followed by the welded plates with the clamped plates having the highest resistance to tearing.     

门式脚手架在已建高层建筑外装修中的应用

介绍门式脚手架在已建高层建筑外排栅中的整体搭设和应用实例。     

箕斗卸载状况的检测方法

介绍了箕斗卸载状况检测方法的原理,分析了各种方法的优点和缺点。使用时应根据具体情况选择合理的检测方法。     

乳化炸药混装车水孔爆破的优越性

该文分析了应用袋装炸药装填水孔爆破产生拒爆、"冲天炮"、根底偏高和爆破效果差等问题,然而应用乳化炸药混装车装填水孔可以解决这些问题,并且爆破后具有根底平整、大块率低、毒气少和综合效益高等优点.以三峡永久船闸旁侧泄水箱涵工程和江苏田湾核电站工程为例进行了分析.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²