高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

WF40防腐蚀涂料在原料水罐上的应用

中国石化股份有限公司洛阳分公司炼油厂污水汽提装置的原料水罐(V303)由于接触的污水中含有H2S,NH3,CO2,CN-,酚等多种腐蚀介质因此经常发生腐蚀泄漏事故。经涂刷WF40玻璃鳞片防腐蚀涂料后,已平稳运行两年。2002年检修检查,涂层完好,仍在继续使用。WF40涂料为环氧型玻璃鳞片涂料,其热膨胀系数与钢质基体接近,因此具有耐热冲击性强等优点。待涂罐体经喷砂除锈到Sa2.5级后,涂底漆2道,中间涂层2道、面漆2道,使干膜厚度达到350μm,可有效防止腐蚀性介质的渗透。     

Cr12型模具钢锻造内部裂纹产生的原因及预防

基于Cr12型钢种的特点，归纳了Cr12钢锻造时内部裂纹的类型，分析了内部裂纹产生的原因并提出了相应的预防措施。     

The application of microencapsulated phase‐change materials to nylon fabric using direct dual coating method

The fabrication of functional textiles able to provide thermal regulation and comfort for the body has attracted increasing interest in recent years. This research investigated fabric coatings containing energy absorbing, temperature stabilizing, phase‐change material microcapsules (PCMMcs), and their methods of application. Specifically, a coated fabric was directly prepared by a dual‐type coating method, in which the PCMMcs were dispersed in a polyurethane coating solution with no binder. The thermal performances of the dual‐coated samples were evaluated by differential scanning calorimetry, and their physical characteristics were examined by scanning electron microscopy, thermal vision camera, porosity, water vapor transmission rate (WVTR), and water entry pressure (WEP) analyses. Furthermore, the microclimate characteristics of the thermally enhanced fabrics were investigated under experimental conditions using a human‐clothing‐environment (HCE) simulator system. The study results confirmed the superior performance of the dual‐coated fabrics in terms of thermal regulation and body comfort, compared with those coated by the dry or wet coating method, because of the improved WEP, WVTR, and thermal performance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

山特维克可乐满公司切削刀具涂层技术的发展

介绍了山特维克可乐满公司切削刀具涂层技术的发展，并对该公司自1979年以来硬质合金涂层产品的发展情况进行了总结。     

薄层隔热保温涂料的研制及应用

常规保温材料的研究以提高孔隙率、提高热阻、降低传导传热性能为主,但其对流传热及辐射传热较难降低。当今以传热机理改进保温材料及保温结构是重要发展方向。文章介绍了一种借鉴国外航天工业用高科技绝热涂层的技术思路,并结合国情研制成功的具有高辐射率的薄层隔热保温涂料,它可弥补常规保温材料的不足。该保温涂料以液态涂料方式存在,干燥后的涂层热阻较大,特别是热反射率高,可有效地降低辐射传热,施工方便,涂层薄,无接缝,附着力好,集防水隔热外护于一体。绝热等级为R21.1,热反射度0.79,热辐射率0.83,固含量54％,性能接近国外同类产品水平,成本仅为国外产品的1/4左右。可直接以涂层方式使用,也可与其他多孔保温材料复合构成低辐射传热结构,作为石油石化行业成品油罐及储罐的隔热保温、管道及设备的保冷及屋面隔热保温涂层使用,综合节能效益高。