High‐performance thermosets with tailored properties derived from methacrylated eugenol and epoxy‐based vinyl ester

A renewable chemical, eugenol, is methacrylated to produce methacrylated eugenol (ME) employing the Steglich esterification reaction without any solvent. The resulting ME is used as a low‐viscosity co‐monomer to replace styrene in a commercial epoxy‐based vinyl ester resin (VE). The volatility and viscosity of ME and styrene are compared. The effect of ME loading and temperature on the viscosity of the VE–ME resin is investigated. Moreover, the thermomechanical properties, curing extent and thermal stability of the fully cured VE–ME thermosets are systematically examined. The results indicate that ME is a monomer with low volatility and low viscosity, and therefore the incorporation of ME monomer in VE resins allows significant reduction of viscosity. Moreover, the viscosity of the VE–ME resin can be tailored by adjusting the ME loadings and processing temperature to meet commercial liquid molding technology requirements. The glass transition temperatures of VE–ME thermosets range from 139 to 199 °C. In addition, more than 95% of the monomer is incorporated and fixed in the crosslinked network structure of VE–ME thermosets. Overall, the developed ME monomer exhibits promising potential for replacing styrene as an effective low‐viscosity co‐monomer. The VE–ME resins show great advantages for use in polymer matrices for high‐performance fiber‐reinforced composites. This work is of great significance to the vinyl ester industry by providing detailed experimental support. © 2018 Society of Chemical Industry     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

Al2O3/Yttria‐Stabilized Zirconia Hollow‐Fiber Membrane Incorporated with Iron Oxide for Pb(II) Removal

Removal by absorptive ceramic membranes can simultaneously absorb and separate metal ions from water. Alumina/yttria‐stabilized zirconia (Al₂O₃/YSZ) hollow‐fiber membranes, fabricated using phase inversion and sintering process, were deposited with iron oxide by an in‐situ hydrothermal process. The results showed that α‐Fe₂O₃ was produced and incorporated across the membranes. A reduction in flux was recorded with the deposition of α‐Fe₂O_3. However, it improved the adsorption capacity for heavy metal adsorption. The adsorption‐separation test demonstrated that the optimized membrane is able to completely remove Pb(II) ions after two hours.     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.