台式毛细管放电X光激光装置调试实验

对自行研制的台式毛细管放电X光激光装置进行了系统调试,在充氩气毛细管负载下,输出电流38kA,电流脉冲前沿40ns,并对有关问题进行了讨论.并在这个装置上开展充氩气毛细管放电荧光光谱实验研究.     

黑龙江联通CDMA网络的特点

简要介绍黑龙江联通CDMA的网络结构、建网原则及CDMA 1X网的主要业务。     

ISDN PBX及X.25网关的管理

本文介绍了ＩＳＤＮ用户一网络接口的管理模型，分析了ＰＢＸ、Ｘ．２５网关的管理功能，对协议测试，管理通信进行了研究并提出模型及实现原则。     

分组交换网上的增值业务

本文介绍了公用和专用分组交换数据网的现状后，说明了开展标准的增值业务系统的重要性。论述了典型的增值业务系统－电子邮件和传真存储转发系统。     

用变角XPS定量分析研究GaAs光电阴极激活工艺

用变角X射线光电子能谱 (XPS)技术分析了GaAs光电阴极的激活工艺 ,定量计算了阴极表面激活层和界面氧化层的厚度和组成。界面氧化物是由于O原子穿过激活层 ,扩散到GaAs与 (Cs,O)激活层的界面上而形成的。导入过量O会增加O GaAs界面层的厚度 ,而对 (Cs,O)激活层厚度影响较小。在激活过程中 ,严格控制和减少每次导入的O量是减少界面氧化层厚度 ,提高灵敏度的重要途径。在第一步激活后的阴极样品 ,通过较低温度的加热和再激活 ,能获得比第一步高出 30 %的光电灵敏度的原因是较低温度加热减少了界面氧化层的厚度和界面势垒     

Thermomechanical fatigue—damage mechanisms and mechanism-based life prediction methods

An existing extensive database on the isothermal and thermomechanical fatigue behaviour of high-temperature titanium alloy EVII 834 and dispersoid-strengthened aluminum alloy X8019 in SiC particle-reinforced as well as unreinv conditions was used to evaluate both the adaptability of fracture mechanics approaches to TMF and the resulting predictive capabilities of determining material life by crack propagation consideration. Selection of the correct microstructural concepts was emphasised and these concepts were, then adjusted by using data from independent experiments in order to avoid any sort of fitting. It is shown that the cyclic /-integral (δJ_eff concept) is suitable to predict the cyclic lifetime for conditions where the total crack propagation rate is approximately identical to pure fatigue crack growth velocity. In the case that crack propagation is strongly affected by creep, the creep-fatigue damage parameter δ_CF introduced by Riedel can be successfully applied. If environmental effects are very pronounced, the accelerating influence of corrosion on fatigue crack propagation can no longer implicitly be taken into account in the fatigue crack growth law. Instead, a linear combination of the crack growth rate contributions from plain fatigue (determined in vacuum) and from environmental attack is assumed and found to yield a satisfactory prediction, if the relevant corrosion process is taken into account.     

多相物质粉末衍射的物相检索

讨论了多相物质粉末衍射的物相检索问题，介绍了XRDS的物相检索软件。这是一种智能型的物相检索程序，考虑了测试数据的不确定度，以及粉末样品和块状样品衍射图谱各自的特点，不仅注意到实际样品中微量物相存在的可能，也注意到块状样品结构有序性的可能。XRDS能够帮助材料工作者同时检出样品中所含的多种物相及其含量，操作简单、结果可靠。     

Conducting composites of poly(N‐vinylcarbazole), polypyrrole,and polyaniline with 13X‐zeolite

N‐vinylcarbazole (NVC) was polymerized by 13X zeolite alone in melt (65°C) or in toluene (110°C) and a poly(N‐vinylcarbazole) (PNVC)‐13X composite was isolated. Composites of polypyrrole (PPY) and polyaniline(PANI) with 13X zeolite were prepared via polymerization of the respective monomers in the presence of dispersion of 13X zeolite in water (CuCl₂ oxidant) and in CHCl₃ (FeCl₃ oxidant) at an ambient temperature. The composites were characterized by Fourier transform infrared analyses. Scanning electron microscopic analyses of various composites indicated the formation of lumpy aggregates of irregular sizes distinct from the morphology of unmodified 13X zeolite. X‐ray diffraction analysis revealed some typical differences between the various composites, depending upon the nature of the polymer incorporated. Thermogravimetric analyses revealed the stability order as: 13X‐zeolite > polymer‐13X‐zeolite > polymer. PNVC‐13X composite was essentially a nonconductor, while PPY‐13X and PANI‐13X composites showed direct current conductivity in the order of 10^?4 S/cm in either system. However, the conductivity of PNVC‐ 13X composite could be improved to 10^?5 and 10^?6 S/cm by loading PPY and PANI, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 913–921, 2006     

舞钢管线钢的开发与生产

系统介绍了舞钢开发的针状铁素体型X70宽厚板的设计思路、工艺特点和实物水平；采用电炉 炉外精炼 连铸 TMCP工艺生产的X70宽厚板满足西气东输专用技术条件的要求，并批量应用在西气东输主干线工程中。     

首钢“川气出川”工程用17.5mmX70管线钢的试制

介绍了首钢试制17.5mm规格高强度、高韧性X70管线钢的生产工艺（成分设计、炼钢和轧钢工艺）及产品的力学性能。在华油钢管厂完成制管（管径为1016mm）以及相应的检验后，所有性能指标全部达到“川气出川”管道工程的技术规范要求。