X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.     

UV-LIGA深度光刻机平滑衍射技术研究

UV-LIGA深度光刻技术是加工微型机电系统的一项重要的微细加工技术。介绍了一种平滑衍射效应的位错强度叠加原理，它采用了蝇眼积分透镜去平滑衍射，并模拟数值计算了硅片表面的光强分布，最后给出了光刻结果。     

X射线衍射线形Fourier变换

采用计算机辅助实验技术，研究X射线衍射线开在仪器宽化修正过程中Fourier系数变化的规律及其影响，结果表明，只要实测线形接近Gauss 分布，Fourier变换就会导致弯勾效应；Forier变换可引起真实线形的尾部波动及大于实际值的宽化，引入边界条件可予以消除，Kα双线形经过Fourier变换后，Fourier纱数与真实Fourier系数存在着一定的差异。通过真实线形的Fourier变换可以修正。     

Preparation and characterization of organic-inorganic poly(ethylene glycol)/WS2 nanocomposite

Layered nanocomposite PEG/WS₂, intercalating oligomeric poly(ethylene glycol) (PEG6000) into the tungsten disulfide host galleries, was synthesized using the exfoliation-adsorption technique. X-ray diffraction revealed that the intercalated oligomer within the host galleries is in a double-layer arrangement with an interlayer expansion of about 8.8 Å. The optimum conditions were explored to prepare the single-phase product with a composition of Li_0.12(PEG)_1.51WS₂. Thermal analyses suggested that the resulting material shows good thermal stability, with the decomposition of the interacted oligomeric chains within the disulfide galleries occurring at around 258 °C. Despite high conductivity of the host material, those of the PEG/WS₂ nanocomposite were found to be high in the order of 1 × 10⁻² S cm⁻¹ at ambient temperature, resulted from the host guest-host charge transfers.     

Influence of the Preheat Treatment on the Microstructure and Properties of X37CrMoV5-1 Steel

The technological properties of the hot-work tool steels depend on their microstructural quality induced by the production process and the heat treatment. One of the frequently applied methods to improve microstructure is preheat treatment. The treatment of carbonitriding X37CrMoV5-1 steel has been investigated in fluidized bed furnaces. Thickness and phase composition have been conducted using optical microscopy Neophot 32 and scanning microscopy, JEOL 5400, after etching in nital.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

小型微/纳米级三坐标测量机的研制

介绍一套低成本小型三维坐标测量机的研制过程，作为微/纳米级超精密测量设备，整体机台结构采用花岗岩材料；X／Y轴的移动平台利用压电材料摩擦驱动与挠性变形原理，长短两行程可达25mm范围及5nm的微位移，藉自行研发的衍射干涉激光尺，位置回馈测量系统可具有0．025nm的分辨率；测量探头在一般DVD光读取头的自动聚焦原理基础上改装，最佳分辨率可达2．5nm，该雏形机适于测量微机电组件、微型器件及膜厚等。     

弱导光纤的标量衍射光束特性分析

仿照罗兰圆光学系统构造罗兰球光学系统 ,在罗兰球中简化电磁波的瑞利 索末菲标量衍射积分公式 ,推导出折射率阶跃分布的弱导光纤LP模衍射场分布和空间频谱的计算公式。提出LP0 1模远场衍射分布存在类似于平面波圆孔夫琅禾费衍射艾里斑的中央亮斑概念 ,并给出中央亮斑角半宽度的计算公式。     

电控平行排列液晶光栅的光衍射特性研究

对电控平行液晶光栅的理论进行了分析,并配以结构原理图。通过对平行排列及90°扭曲排列液晶指向矢的计算,得出液晶盒中相应的折射率、相位差与电压之间的关系图,两者经比较证明平行排列更具适用性,并在实验中观测到了平行排列液晶光栅衍射特性与电压的关系。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.