EXL能谱仪薄样品X线的定量分析

研究了Link公司能谱仪中RTS软件（薄膜定量分析软件）可靠性及适用性。实验结果表明：RTS软件定量分析结果误差较小。但对C、N、O等轻元素定量分析，试样厚度小于1500以下时，结果才比较可靠。     

Comparison of interfaces in Ti composites reinforced with uncoated and TiB2/C-coated SiC fibres

Interfaces play an important role in determining the mechanical properties of composite materials. The interfaces established between a titanium-alloy matrix (Ti-6Al-4V) and uncoated and TiB₂/C-coated SiC fibres are analysed by scanning electron microscopy, transmission electron microscopy and X-ray techniques. Emphasis is placed upon the interfacial morphology and microstructure, identification of reaction products, and the stability of the coating layer. Complex multi-reaction layers are observed frequently in the interfacial zones. Previous, often contradictory, reports about the interlayers are reviewed. Experimental observation demonstrates that the type and distribution of interlayers vary in a given system, due to prolonged treatment of the samples at temperature. The formation and distribution of the interlayers are discussed further, with respect to these and previous findings. Methods of reducing interfacial reactivity are discussed.     

X-ray spectroscopy and local structures in glasses

X-ray spectroscopy which is a combination of two techniques, namely x-ray absorption near edge structure (xanes) and extended x-ray absorption fine structure (EXAFS) analyses, is a unique technique for the study of local structures in glasses. Availability of synchrotron radiation sources has made the technique quite attractive and useful because the photon flux from synchrotrons is very intense and polarized. In this article, a brief summary ofxanes andEXAFS techniques is given along with a few applications to the study of local structures in glasses. Communication No. 323 from Solid State and Structural Chemistry Unit.     

X射线机不是计量器具

计量学的基本理论指出，X射线机不具有计量器具的属性。国家的计量法规并未将X射线机定为计量器具。目前存在的JJG 40—2001《X射线探伤机》检定规程，将X射线探伤机与X射线检测技术相互混淆，将X射线探伤机的某些技术性能，说成所谓的X射线探伤机的“计量性能”，不仅违反计量学基本理论，而且也不符合射线检测技术实际。从计量学理论和射线检验实际经验只能得到X射线机不是计量器具的结论。     

Influence of Mn and Cu addition on the hyperfine parameters of amorphous and nanocrystalline FeCoNbB alloys

The effects of Cu and Mn addition on the hyperfine field of FeCoNbB HITPERM alloys are discussed from Mössbauer spectrometry. Amorphous and nanocrystalline samples at different stages of the nanocrystallization were studied. The effect of Cu addition correlates with the observed refinement of the microstructure. Mn mainly partitions to the matrix, decreasing the average hyperfine field of the amorphous matrix, although some Mn remains in the nanocrystalline grains, presumably, in a concentration below the maximum solubility of Mn in -Fe.     

Taxonomy for protective ability of rust layer using its composition formed on weathering steel bridge

For a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge, the relationship between the corrosion rate of the bridge and the composition of the rust layers formed on the girders was first investigated. These corrosion rates were clearly classified by the protective ability index (PAI) of α/γ^∗ and (β + s)/γ^∗, where α, γ^∗, β and s are the mass ratio of crystalline α-FeOOH, the total of γ-FeOOH, β-FeOOH and the spinel-type iron oxide (mainly Fe₃O₄), β-FeOOH and spinel-type iron oxide, analyzed by XRD, respectively. The inequality of the former index α/γ^∗ > 1 expressed the protectiveness criterion of the rust layer, while that of the latter index, (β + s)/γ^∗< 0.5 or > 0.5, classified the corrosion rate of the non-protective rust layer. The PAI is useful for a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge and is an important item for the corrosion assessment of the bridge.     

Structure, hyperfine interactions and magnetization studies of mechanically alloyed Fe50Ge50 and Fe62Ge38

X-ray diffraction, Mössbauer spectroscopy and magnetization measurements were used to study the structure and some magnetic properties of Fe₅₀Ge₅₀ and Fe₆₂Ge₃₈ prepared by mechanical alloying from the elemental powders. In both cases in the early stages of milling the intermediate paramagnetic FeGe₂ phase was formed. The mechanical alloying process of Fe₅₀Ge₅₀ resulted in the formation of the paramagnetic FeGe (B20) phase with an average crystallite size of about 15 nm. In the case of the Fe₆₂Ge₃₈, the ferromagnetic Fe₅Ge₃ (β) phase with a Curie temperature of about 430 K was obtained. The average crystallite size was about 9 nm. The average hyperfine magnetic field of about 16 T allowed it to determine that more than four germanium atoms exist in the nearest environment of the ⁵⁷Fe isotopes in the Fe₅Ge₃ phase.     

X射线透射成像技术原位追踪混凝土吸水过程

为了表征二维混凝土的传输过程,制备厚度为1 mm的混凝土薄片. 采用X射线透射成像（TXR）技术,联合扫描电镜、背散射和能谱分析技术（SEM/BSE/EDS）原位追踪水在2维混凝土薄片中的毛细自吸过程. 测试不同质量分数CsCl溶液对X射线透射图像的增强效果. 结果表明,CsCl能够提高吸水过程中混凝土薄片的TXR图像对比度,使得水在混凝土中的渗流路径更清晰、可辨. 水泥浆体在吸收CsCl后,扫描电子背散射图像的对比度显著增强. 不同位置铯原子的EDS能谱结果验证了TXR技术确定吸水前锋位置的准确性.     

X射线衍射-拉伸法测薄膜应力

薄膜应力的测量一直是一个困难的问题。本文尝试用一种新的方法——X射线衍射-拉伸法,对薄膜的应力进行检测,与侧倾法实验结果相比较,X射线衍射-拉伸法更为准确与可靠。