Topology optimization of trusses using genetic algorithm,force method and graph theory

In this article size/topology optimization of trusses is performed using a genetic algorithm (GA), the force method and some concepts of graph theory. One of the main difficulties with optimization with a GA is that the parameters involved are not completely known and the number of operations needed is often quite high. Application of some concepts of the force method, together with theory of graphs, make the generation of a suitable initial population well‐matched with critical paths for the transformation of internal forces feasible. In the process of optimization generated topologically unstable trusses are identified without any matrix manipulation and highly penalized. Identifying a suitable range for the cross‐section of each member for the ground structure in the list of profiles, the length of the substrings representing the cross‐sectional design variables are reduced. Using a contraction algorithm, the length of the strings is further reduced and a GA is performed in a smaller domain of design space. The above process is accompanied by efficient methods for selection, and by using a suitable penalty function in order to reduce the number of numerical operations and to increase the speed of the optimization toward a global optimum. The efficiency of the present method is illustrated using some examples, and compared to those of previous studies. Copyright © 2003 John Wiley & Sons, Ltd.     

线性调频信号检测方法的研究

在线性调频信号体制雷达的数字脉冲压缩系统中对数字脉压后的脉冲串进行DFT相参处理时，若采样时刻偏离脉压回波的峰值时刻，不同的采样频率使得DFT相参积累后的信噪比会有不同程度的损失。本文详细分析了采样频率分别为20MHz和10MHz时对信号相参积累的影响，并对幅值检测和M／N检测两种检测方法的检测性能进行了比较，仿真结果表明，M／N检测优于幅值检测。     

超声波清洗在贵/廉金属复合材料生产过程的应用研究

本文结合“ODS清洗剂消费淘汰项目”的实施，并对新型超声波清洗机及新型ODS清洗液进行了工艺试验，阐述了超声波清洗技术是贵／廉金属复合材料生产过程中无可替代的清洗技术。     

晶须取向对SiCw/6061Al复合材料热压缩变形行为的影响

采用SEM 和 Magiscan-2A 图像分析系统研究了晶须取向对SiCw/6061Al复合材料在300℃压缩变形行为的影响.结果表明:晶须取向影响着晶须折断程度和转动角度; 随着晶须取向角的增加,晶须转动和折断行为所导致的软化效果下降.同时晶须取向也影响复合材料的热压缩应力-应变曲线的形状.在热压缩变形过程中,晶须取向角为0°和30°的复合材料表现出明显应变软化现象, 晶须取向角为45°的复合材料无明显软化现象.晶须取向角为90℃的复合材料表现出应变硬化现象.     

技术性贸易壁垒对国际贸易的影响及其对策

本文介绍了国际技术贸易的原则，论述了各种对策以解决技术性贸易壁垒。     

A concept for the generation of out-of-plane distortion from tailored FRP laminates

The phenomenon of thermally induced distortions in unsymmetrical laminates is well understood, and it may be shown that a square, unsymmetrical 0.90 laminate will tend to form two stable geometries with a snap-through phenomenon between them. This paper discusses laminates in which at each point the lay-up is symmetrical across the laminate mid-plane, but which still exhibit multiple stable geometries. The number of stable geometries can be controlled by the details of the lay-up from the minimum of two to, in principle, an unlimited number. In addition it will be shown how a similar process can be used to generate multiple stable stress states and geometries in unidirectional laminates. This paper represents a very preliminary experimental investigation of the design space available for such composite laminates. Possible applications of composites with multiple stable geometries are noted.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

珠海台网络硬盘多频道数字播控系统

叙述了以视频服务器为中心构建的网络化多频道自动播出系统的实践、见解和系统的特点。该系统着重考虑了视频服务器选型、系统可靠性、网络化控制及监控、信号共享等问题；同时，实现了多路同时上载、多路边播边上载，以及自动延时播出等功能。