标准型直燃机在严寒地区应用探讨

介绍了标准型直燃机的分类、原理及长庆至呼和浩特输气管道工程冷冻供热站的设计实例 ,重点论述了标准型直燃机在严寒地区使用的利弊     

The intervalley X6→Γ6, L6 scattering time in GaAs measured by ultrafast pump-probe infrared absorption spectroscopy

A direct measurement of the dynamics of electrons in the X₆ valley for a GaAs crystal by time-resolved absorption spectroscopy is reported for the first time. IR picosecond probe pulses were used to monitor the growth and decay of the population in the X₆ valley subsequent to excitation by a 527 nm pump pulse. The intervalley X₆→Γ₆, L₆ scattering time t_x of 0.70 ± 0.50 ps is determined and the crossection for the X₆→X₇ transition is estimated to be 1.8 × 10⁻¹⁶ cm².     

测量高功率激光的体吸收能量计

叙述了体吸收激光能量计的特点，介绍了其标定方法，给出了其技术参数。体吸收激光地的推广应用取得了广泛的社会效益。     

Investigation of fusion reactions in palladium and titanium tritide using galvanostatic,coulometric, and hydrogen permeation techniques

We describe several electrochemical methods used to investigate the possibility of cold fusion phenomena in palladium and titanium tritide cathodes. We performed long-term (up to 77 days) electrolysis experiments with electrochemical cells of the University of Utah type at current densities as high as 1 A/cm², while monitoring neutron and tritium levels. With some cells, we pulsed the current to determine if neutron bursts would result. In another cell, we used titanium tritide as the cathode to determine if D-T reactions yielding neutrons would occur. In no instance were levels of neutrons or tritium significantly above background except in the titanium tritide cell where isotopic exchange, occcurring between the electrode and the electrolyte, resulted in significant tritium levels. We also combined x-ray photoelectron spectroscopy (XPS) and electrochemical hydrogen permeation experiments to determine the effectiveness of various Pd surface treatment procedures on the resultant electrochemical hydrogen absorption efficiency. Electroanalytical and thermal desorption/gas analysis techniques indicated the maximum loading of H in Pd was to a ratio of HPd=0.8.     

热处理对多孔铝合金压缩吸能性能的影响

采用渗流铸造工艺 ,制备了Al Si系多孔铝合金 ,讨论了其压缩变形特征及能量吸收性能 ,分别对ZL10 1、ZL111两种多孔铝合金进行T6热处理 ,研究了热处理对这两种多孔铝合金压缩吸能性能的影响。研究结果表明 ,热处理能够提高多孔铝合金的能量吸收能力 ,对屈服强度及能量吸收效率也有显著的影响 ,为提高多孔铝合金的压缩性能 ,应尽可能施行热处理     

氮气氛下直拉硅中氮含量的红外光谱测定

提出了利用直拉硅中与氮有关的特征红外吸收峰９６３、９９６、１０８１－１及１０２７ｃｍ－１确定直拉硅中氮含量的计算公式，并进行了多种样品实测。该法克服了只用９６３ｃｍ－１峰测定直拉硅中氮使结果偏低的弊病，方法相对偏差为５％～２０％     

相对压强对白炭黑氮吸附表面积测试稳定性的影响

研究相对压强对白炭黑氮吸附表面积测试稳定性的影响。结果表明:在相同液氮纯度、脱气温度、脱气时间、氮吸附点数量条件下,与相对压强范围为0.05~0.1时相比,相对压强范围为0.05~0.2时白炭黑的氮吸附表面积测量值偏低,且差值随氮吸附表面积的增大呈增大趋势;相对压强范围较小时,氮吸附表面积测试结果的线性相关因数较大,再现性较好,测试结果较稳定。     

A Strategy of Liquid-Grafted Slippery Sponges with Simultaneously Enhanced Absorption and Desorption Performances for Crude Oil Spill Remediation

Crude oil spill accidents pose a worldwide environmental threat. Oleophilic and hydrophobic absorbents that can selectively absorb oil from water have shown promising application potential in oil spill remediation. Simultaneous optimization of the absorption and desorption speed of absorbents towards oil is highly desirable for their recyclable usage, but remains a great challenge, because these two properties are generally conflicting. Here, a facile and ingenious strategy is proposed to tackle the above challenge via surface modification of porous sponges with highly flexible linear polydimethylsiloxane (LPDMS) brushes. The LPDMS brushes feature liquid-like properties at room temperature owing to its extremely low glass transition temperature, and act as a covalently-grafted lubrication layer throughout the 3D network channels of the sponge, which can minimize contact angle hysteresis and reduce friction between oil and sponge channel. Compared to the prevalent cross-linked polydimethylsiloxane (CPDMS) modification strategy, sponges modified with LPDMS brushes not only shows significantly enhanced absorption speed, but also exhibits superior desorption dynamics towards viscous crude oils. The design strategy of slippery sponges with liquid-like molecules may open a new avenue for developing advanced absorbents with simultaneously enhanced absorption and desorption performances for liquid separation and purification applications.     

低碳铸铁增碳技术

介绍了增碳剂在铁液中溶解的机理和目前主要采用的投入法和喷粉法增碳工艺。影响增碳剂吸收率的因素有增碳剂粒度和加入量、铁液温度、搅拌时间以及铁液化学成分。增碳后可使铸铁组织改善、性能明显提高。目前在 内，对在反射炉内熔化铸铁时炉内无法增碳，包内增碳又有温降、收得率要求高的困难等问题，有待研究解决。     

红外辐射吸收法测量火焰温度

简述了几种温度测量的方法，介绍了红外辐射吸收法测温原理及实验装置，并对稳定的煤气火焰进行温度测量，试图在此基础上测量固体推进剂火焰的温度。