芯壳乳液胶粘剂的研究

介绍乙酸乙烯酯－丙烯酸丁酯－丙烯酸芯结构乳液的制备方法，并将它们的性能与均匀共聚乳液作了测试与比较。     

聚醋酸乙烯乳液缩醛化的改性研究

本文介绍了为提高聚醋酸乙烯乳液稳定性、耐水性和防冻性而进行缩醛化改性的原理，并确定了最佳工艺条件即甲醛与聚乙烯醇的配比为０．４５～０．５０。     

新型技术用于乳状液膜法脱酚的进一步研究

本文对模拟的含酚废水,采用新型技术对乳状液膜法脱酚进行了进一步的探讨。对所采用的制乳设备———撞击流-旋转填料床对制乳率、提取设备———旋转填料床对脱酚率、破乳设备———无机微孔膜法破乳的重要参数(如透过压方式、膜孔径等对膜通量和破乳率的影响)进行了研究。并且讨论了破乳后的油相回用情况。实验结果表明:撞击流-旋转填料床的制乳效率可达99.90 %以上,脱酚率可达99%左右,且瞬间完成;膜孔径越小,破乳率越高,膜通量越小;外压内抽方式的破乳效果优于单外压方式的破乳效果。对于粒径为5～2 5 μm乳液,用膜孔径为2 .0 μm的SiC微孔膜,在外压为6 0kPa、内负压为30kPa的外压内抽破乳方式下破乳,破乳率可达96 .4 % ,膜通量可达90 0L·(m2 ·h) -1。     

邻羟基环己基丙烯酸酯光聚合动力学研究

采用实时红外光谱技术(RTIR)研究了邻羟基环己基丙烯酸酯(HCA)光聚合反应动力学,探讨了光照强度、光引发剂种类和浓度对其光聚合动力学的影响,并与脂肪族羟基丙烯酸酯单体丙烯酸羟乙酯(HEA)进行了对比。结果表明,最终双键转化率和相对反应速率随光强增大而增加;光引发剂浓度对最终双键转化率和反应速率的影响随引发剂不同呈现不同规律;与HEA相比,HCA具有更高的反应活性,但最终双键转化率较低。     

Oxidative flavour deterioration of fish oil enriched milk

The oxidative deterioration of milk emulsions supplemented with 1.5 wt‐% fish oil was investigated by sensory evaluation and by determining the peroxide value and volatile oxidation products after cold storage. Two types of milk emulsions were produced, one with a highly unsaturated tuna oil (38 wt‐% of n‐3 fatty acids) and one with cod liver oil (26 wt‐% of n‐3 fatty acids). The effect of added calcium disodium ethylenediaminetetraacetate (EDTA) on oxidation was also investigated. Emulsions based on cod liver oil with a slightly elevated peroxide value (1.5 meq/kg) oxidised significantly faster than the tuna oil emulsions, having a lower initial peroxide value (0.1 meq/kg). In the tuna oil emulsions the fishy off‐flavour could not be detected throughout the storage period. Addition of 5—50 ppm EDTA significantly reduced the development of volatile oxidation products in the cod liver oil emulsions, indicating that metal chelation with EDTA could inhibit the decomposition of lipid hydroperoxides in these emulsions. This study showed that an oxidatively stable milk emulsion containing highly polyunsaturated tuna fish oil could be prepared without significant fishy off‐flavour development upon storage, provided that the initial peroxide value was sufficiently low.     

负离子乳胶漆的研究及应用进展

介绍了空气中负离子的作用、负离子乳胶漆释放负离子的原理和国内外负离子乳胶漆产品的研发进展。     

A new core–shell type fluorinated acrylic and siliconated polyurethane hybrid emulsion

A novel core–shell type fluorinated acrylic and siliconated polyurethane (FSiPUA) hybrid emulsion was prepared by seeded emulsion polymerization using siliconated polyurethane (SiPU) as a seed and forming the structure with SiPU as a shell and the copolymer of butyl acrylate (BA) with 2,2,2-trifluoroethylmethacrylate (TFEMA) as a core. SiPU was synthesized using isophorone diisocyanate (IPDI), polytetramethylene ether glycol (PTMG), polypropylene glycol (PPG), dihydroxybutyl-terminated polydimethylsiloxane (PDMS), dimethylol propionic acid (DMPA), 1,6-hexanediol (HDO) and triethylamine (TEA). The contents of siloxane and fluorine were determined according to the feed ratio. Fourier transform infrared spectroscopy (FTIR) was used to identify the chain structure of SiPU and FSiPUA. Investigation of transmission electron microscopy (TEM) confirmed the core–shell structure of FSiPUA emulsion and gave the particle size at about 50 nm. The measurement results of water contact angles and the solvent absorptions in water and n-octane for cured films showed that the water and the oil repellency for FSiPUA had been improved significantly with a suitable content of fluorine and siloxane.     

两性乳化剂体系对有机硅改性丙烯酸酯乳液合成的影响

采用新型琥珀酸类两性乳化剂(A1)与非离子乳化剂壬基酚聚氧乙烯醚(CA407)复配体系,合成了有机硅γ-甲基丙烯酰氧基丙三甲氧基硅烷(A174)改性的丙烯酸酯乳液。系统研究了两性乳化剂体系与非离子乳化剂复配比例、用量及乳化剂在种子乳液与预乳液中分布比例(R/F)E对乳液聚合及其性能的影响。研究表明:乳化剂配比m(A1)∶m(CA407)=30∶70时,乳液聚合稳定性及抗电解质稳定性较好;乳化剂用量越大,乳胶粒径越小,粒径分布越宽,乳液黏度越大,涂膜吸水率也越大;乳化剂在种子乳液与预乳液中的分布比例主要影响乳液聚合的稳定性。同时通过TEM乳胶粒形态分析及DSC涂膜的玻璃化转变温度分析认为,A174主要在乳液聚合时分布在乳胶粒表面,易水解交联。     

NCO含量对聚氨酯-丙烯酸酯复合乳液性能的影响

以甲苯二异氰酸酯(TDI-80)、聚醚二元醇(N210)、二羟甲基丙酸(DMPA)和甲基丙烯酸甲酯(MMA)为主要原料，采用原位乳液聚合法，合成聚氨酯-丙烯酸酯(PUA)复合乳液。在保证DMPA含量、中和度等不变的情况下，研究了NCO／OH物质的量之比对乳液的性能及外观的影响。