Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

串行及并行A/D转换器在高速数据采集中的采样差别性分析

串行和并行接口模式是A/D转换器诸多分类中的一种,但却是应用中器件选择的一个重要指标.在同样的转换分辨率及转换速度的前提下,不同的接口方式不但影响了电路结构,更重要的是将在高速数据采集的过程中对采样周期产生较大影响.本文通过12位串行ADC ADS7822和并行ADC ADS774与AT89C51的接口电路,给出二者采样时间的差异性.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

GPRS手机入网测试自动化

全球移动通信系统(GSM)广泛的应用于现代通信系统就在于其良好的兼容性,不同的移动设备之间在遵守一定协议规范的条件下可以相互通信;本设计测试的是GSM第11系列GSM11.10,他包括诸多测试项,只对接收机参考灵敏度电平在GSM900与DCS1800两个频段进行测量。给出了传统形式下的手动测试和自动测试平台的比较,并建立了收信机参考灵敏度指标的自动测试平台。     

羧酸系列集油剂的水面集油性能

研究了十二烷酸、十四烷酸、十六烷酸和十八烷酸在淡水中的集油能力。结果表明，这4种羧酸在淡水表面的表面膜压随其分子中碳数的增加而增大。其中后两者的表面膜压高达45～50mN／m，显著高于各类油膜膜压，满足集油剂对表面活性物质膜压的要求。4种脂肪羧酸在淡水中使柴油油膜的收缩率在1min时达到最大值，分别为80．0％、81．8％、83．8％和88．2％。它们的己醇、正庚醇、正辛醇、仲辛醇溶液的集油持续性，总体上随羧酸分子碳数增加而增大。其中十六烷酸和十八烷酸集油能力非常接近，它们的正庚醇、正辛醇和仲辛醇溶液使柴油膜面积收缩率在120h后仍保持在66．0％～70．2％。该类集油剂毒性低，易为生物降解，有实际应用前景。