Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

阴离子表面活性剂测定方法的探讨

本文对“阴离子表面活性剂的测定方法”进行探讨,优化了显色剂、萃取剂的用量及萃取频率等分析条件,有效地降低了方法的检出浓度,提高了分析精度及准确度,节约大量试剂。本法最低检出浓度的0.019mL/L。     

Hyperion, IKONOS, ALI, and ETM+ sensors in the study of African rainforests

The goal of this research was to compare narrowband hyperspectral Hyperion data with broadband hyperspatial IKONOS data and advanced multispectral Advanced Land Imager (ALI) and Landsat-7 Enhanced Thematic Mapper Plus (ETM+) data through modeling and classifying complex rainforest vegetation. For this purpose, Hyperion, ALI, IKONOS, and ETM+ data were acquired for southern Cameroon, a region considered to be a representative area for tropical moist evergreen and semi-deciduous forests. Field data, collected in near-real time to coincide with satellite sensor overpass, were used to (1) quantify and model the biomass of tree, shrub, and weed species; and (2) characterize forest land use/land cover (LULC) classes.The study established that even the most advanced broadband sensors (i.e., ETM+, IKONOS, and ALI) had serious limitations in modeling biomass and in classifying forest LULC classes. The broadband models explained only 13-60% of the variability in biomass across primary forests, secondary forests, and fallows. The overall accuracies were between 42% and 51% for classifying nine complex rainforest LULC classes using the broadband data of these sensors. Within individual vegetation types (e.g., primary or secondary forest), the overall accuracies increased slightly, but followed a similar trend. Among the broadband sensors, ALI sensor performed better than the IKONOS and ETM+ sensors.When compared to the three broadband sensors, Hyperion narrowband data produced (1) models that explained 36-83% more of the variability in rainforest biomass, and (2) LULC classifications with 45-52% higher overall accuracies. Twenty-three Hyperion narrowbands that were most sensitive in modeling forest biomass and in classifying forest LULC classes were identified and discussed.     

用Tow-Thomas电路设计含有限非零传输零点有源滤波器的方法

Tow-Thomas电路是一种实现全极点滤波器的典型电路。本文给出了用Tow-Thoms电路设计含有限非零传输零点有源滤波器的方法，从而使Tow-Thomas电路可用于单片集成滤波器电路。而文中给出的公式可用于计算外接元件。设计实例表明了文中给出的计算公式的正确性。     

TCP/IP网络的动态模型描述

拥塞现象成为TCP/IP网络发展面临的一个重要问题。因此，拥塞控制对TCP/IP网络的鲁棒性和稳定性具有重要作用。目前，网络拥塞控制策略主要包括两类：端到端的控制机制，如TCP拥塞控制算法；网络内部的主动队列管理(AQM)策略。但由于缺乏对网络系统动态特性的了解，这些拥塞控制策略大都基于专家经验，并没有建立完整的理论分析框架。为此，本文从数据流的角度出发，通过建立网络基本单元状态方程模型来实现IP网络系统的数学解析模型，然后用混杂系统来描述TCP带有拥塞控制策略的数据传输过程，建立了TCP/IP网络的动态模型，为网络系统中动态性能的分析、拥塞控制策略的设计奠定了基础。实验结果表明，该数学模型与NS仿真实验的结果相一致。     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

Level set and geodesic active contours based measurement of material removal between serial sections

The measurement of the thickness of material removed between serial sections is a crucial step of three-dimension reconstruction. Geodesic active contours is an efficient method for contour detection of objects on an image. The indents on the SiC/Al composite micrographs are segmented by using level set and geodesic active contours. After getting the contours of the indents, we calculate the distance from the uppermost pixel to the lowermost pixel to get the vertical diagonal length, and calculate the distance from the leftmost pixel to the rightmost pixel to get the horizontal diagonal length of each contour. Then the final length of each diagonal is acquired by averaging the vertical diagonal length and the horizontal diagonal length, respectively. The Vickers’ indenter is made by a square pyramidal-shaped diamond with opposite faces at an angle of 136°, so the thickness of material removed between two serial sections and the length difference of the diagonals on the two serial sections has a definite geometrical relation. Thus the thickness of material removed between two serial sections is acquired using the geometrical relation.     

硫酸盐浆厂污水处理工程及单元技术特点

本文简略介绍云南某硫酸盐浆厂污水处理工程采用的国内不多见的污水单元技术，并对其先进性和实用性效果进行评价和探讨。