小议变动成本法的合理性

企业对盈亏临界点的计算通常是以变动成本法为基础，但也有以制造成本法为计算基础的，对于这两种成本方法计算的几种盈亏临界点的情况，本文结合案例，通过比较分析认为：盈亏临界点的计算应当以变动成本法为基础更为合理。     

十二烷硫基硼酸铈的合成及摩擦学行为研究

合成了油溶性化合物十二烷硫基硼酸铈(简称CeDMB)，并用作润滑油添加剂。采用四球摩擦试验机和环—块试验机评价了其抗磨减摩性能。结果表明，十二烷硫基硼酸铈使HVI500基础油的抗磨性能得到明显改善，承载能力明显提高，摩擦系数明显降低。扫描电子显微镜(SEM)观察证实磨斑表面含有沉积物膜，结合X—射线光电子能谱(XPS)分析，可以推断添加剂在摩擦过程中发生摩擦化学反应，生成的Ce2O3、CeO2和B2O3沉积在摩擦副表面，形成润滑膜，从而改善其抗磨减摩性能。     

绿色供应链管理的基本原理

人口、资源与环境三者之间的矛盾日益突显，要求制造业提高其活动与环境的相容性。绿色供应链管理是从系统的观点与集成的思想出发解决制造业与环境之间冲突的有效方式。从可持续发展的思想出发建立了绿色供应链的概念模型，分析了绿色供应链管理的目标，在此基础上探讨了绿色供应链管理的基本原理，认为共生原理、循环原理、替代转换原理与系统开放原理是实施绿色供应链管理应该遵循的基本原理。     

建筑陶瓷企业实施精益生产研究

分析了建筑陶瓷企业实施精益生产的条件和当前推行精益生产的主要障碍，对应用中存在的问题进行了分析并提出了相关建议。     

Tandem queues with general blocking: A unified model and comparison results

We study tandem queues with finite intermediate buffers and develop a general blocking scheme that unifies and generalizes various blocking schemes previously studied in the literature, such as manufacturing blocking, communication blocking, kanban blocking and its variations. In the general blocking scheme, job movement and service at each stage are controlled by three parameters, which represent, respectively, the upper limits (at that stage) on work-in-process inventory, finished goods inventory, and buffer space. We derive a set of recursive equations that characterize the dynamics of the system, in terms of the job completion and departure processes, and establish comparison results for these processes in the settings of stochastic ordering, variability ordering and stochastic convexity. Free of distributional assumptions, the results provide characterization of system behavior with respect to the control parameters as well as to the arrival and service processes. We also compare system performance under two different modes of operation: make-to-order versus make-to-stock, and demonstrate the trade-off between improving service and reducing inventory. Numerical studies are also presented to illustrate the diversity of performance trade-off, including composition of inventory, offered by the general model.Supported in part by NSF under grant ECS-89-96201.     

抽油机球铁齿轮的化学成分及生产工艺

为提高抽油机减速器齿轮铸件的机械性能，提出以Sn代替Mo作为合金元素，并通过试验确定了合理的Si、Cu、Sn的加入量。指出Si加入量应控制在1．9％－2．1％范围内，同时加入0．36％～0．9％的Cu和0．025％～0．07％的Sn，可保证球铁的强度和延伸率都满足QT700－2的要求。鉴于试件与实际铸件的表面硬度有一定的差值，为提高铸件表面硬度，进行了余热正火试验，并给出了铸件在铸型内的时间－冷却温度曲线。最后根据球铁化学成分的选择结果，进行了齿轮生产试验。     

On modeling the design of cellular manufacturing systems

A new optimization model is discussed for the design of cellular manufacturing systems. It is based on an integer programming formulation that updates some other models by eliminating redundant machine assignment and cost coefficients dependent on cell configuration. To reduce computational burdens, a simplified integer programming model and a decomposition algorithm are proposed. Several computer solutions were performed to evaluate the performance of the new model. The computational results are discussed.     

柔性制造系统的负荷分配及路径规划方法

柔性是柔性制造系统（ＦＭＳ）的一个基本优点，但这一基本优点却往往被人们忽视，许多现在运行的ＦＭＳ不是缺乏柔性，就是没能充分利用可获得的柔性来提高生产效率。柔性制造系统的负荷分配和路径规划问题正是这种柔性的一个主要方面，然而，路规划决策却往往被。其中一个主要原因人们仍不能从传统的生产管理概念中解放出来。本文在明确概念区分的基础上，提出了一种柔性制造系统的负荷分配和路径规划的线性规划模型，其主要特点是     

金属表面柴油机油沉积物的反射红外光谱法研究

利用镜反射红外光谱法研究了ＣＣ级柴油机油中添加剂对成漆板板面漆膜组成的影响：考察了成漆板漆膜组成与Ｃａｔ．１Ｈ２活塞环台漆膜组成的相关性。试验结果对柴油机油的研制和应用有一定指导作用。     

Development and implementation of a NURBS curve motion interpolator

This paper deals with the issues of development and implementation of a real-time NURBS interpolator for a six-axis robot. Using an open-architecture controller system as a testbed, a real-time NURBS curve interpolator was developed, implemented and tested. Sample runs were conducted with the resulting trajectories measured in real-time during robot motion. The resulting trajectories are analyzed, discussed and compared with those from a commonly used point-to-point approximation technique. The real-time NURBS curve interpolator's feasibility, advantages and related issues are also discussed.