膨胀剂对约束条件下UHPC早期抗裂性能影响的试验研究

超高性能混凝土(UHPC)在钢桥面铺装结构中由于铺装材料受到钢板、栓钉等的约束,加上材料本身水胶比小,更易收缩,早期容易承受拉应力导致开裂。通过在拌和过程中添加膨胀剂可以起到减小收缩的作用,但该方法对于约束条件下的UHPC铺装的早期抗裂性能提升是否有促进作用,仍需通过更多试验进行合理评估和深入研究。通过圆环法对3组不同配方的UHPC在均匀约束条件下的早期抗裂性能进行定量测试,并将试验数据进行回归分析和计算,得到了各组的平均应力发展速率,进而评估了各组的开裂风险等级。试验结果表明,通过在UHPC中加入适量膨胀剂,可使其最终收缩应力减小,并可降低其收缩应力发展速率,进一步降低其在约束条件下的开裂风险。     

Significant population genetic structuring in Rhyzopertha dominica across Turkey: Biogeographic and practical implications

Rhyzopertha dominica is a key pest of stored grain. Understanding the movement of this beetle on broad geographic scales is crucial, particularly when developing strategies to prevent the spread of phosphine resistance. We assessed population genetic structuring in this pest across Turkey, using a combination of mitochondrial (cytochrome oxidase I) and microsatellite markers. In addition, we screened samples for Wolbachia, as this endosymbiont has previously been suggested to be associated with low mitochondrial genetic diversity in this beetle. Mitochondrial genetic diversity was low, with only six haplotypes identified. The genetic diversity was, however, substantially higher than that previously found in Australia or India, suggesting that R. dominica may have originated in the Middle East. Wolbachia were detected only at a single site, indicating they are not impacting the mitochondrial genetic diversity of R. dominica across Turkey. Microsatellite markers indicated there is significant geographic genetic structuring across Turkey, even among sites less than 100 km apart, suggesting there is little movement of beetles across regions within the country. This contrasts with the significantly higher levels of gene-flow found in Australia and the United States. We suggest that the limited movement of beetles across Turkey may be due to a combination of the historically localised agricultural practices (which limits anthropogenic movement among regions), and the mountainous landscape (which limits active flight among regions). Our results demonstrate that the movement of stored product pests may differ significantly across studies conducted in different countries. As a consequence, phosphine resistance management strategies must incorporate region specific information on the extent of beetle movement.     

高温高盐高含水油藏提高水驱采收率配套技术

针对江汉油区高温高盐高含水油藏的储层条件,应用国内外油藏精细描述、油藏工程最新理论与技术,提出了高含水油田合理钻加密井、完善注采井网、水平井挖潜、不稳定注水及高温高盐油藏采油工艺配套技术措施,形成了一套适应高温高盐高含水油藏提高水驱采收率的配套技术。     

炼油厂碱性污水生物催化氧化预处理工艺研究

在对炼油厂碱性污水水质分析的基础上,提出采用生物催化氧化工艺对碱性污水进行预处理。试验结果表明,在水力停留时间为4 h,曝气量(标准状态)为8 m3／h的条件下,碱性污水的硫化物去除率可达90％以上,出水中的硫化物平均值为15．2 mg/L,CODCR、酚和油的去除率分别为47．5％,44．1％,50．8％,其中CODCR体积负荷为3．85 kg／(m3·d),是传统生化处理的10倍, 达到了污水预处理的目的。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

MIM隧道发光结的负阻现象

本文介绍了薄膜隧道发光结的基本结构、发光机理，阐述了其Ｉ－Ｖ特性中的负阻现象。简单介绍了ＭＩＭ结构负阻的几种解释，根据热像仪照片和低温测试结果分析，再结合Ｄｅａｒｍａｌｅｙ导电模型，我们提出了ＭＩＭ负阻的物理模型，理论与实验符合较好，最后分析了负阻现象的应用前景。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

Process monitoring using auto-associative,feed-forward artificial neural networks

The potential of using artificially simulated neural networks as intelligent, adaptive process-monitoring devices is discussed. The investigation is considered as a method for automatic, intelligent exception reporting for quality control applications. The technique is also compared with the conventional statistical approaches of principal component analysis and Kohonen's feature map. The applications of the technique in aerospace and manufacturing environments are presented and a possible extension of the method to incorporate a diagnostic function is discussed.Seconded from Cheltenham and Gloucester College of Higher Education as a Royal Society/SERC Research Fellow at Smith's Industries Aerospace and Defence Systems, Bishop's Cleeve, Cheltenham, UK.     

金属换热器选用经济分析

本文以系统节能和提高综合经济效益的观点，分析了金属换热器传热系数的影响因素及提高途径；气流阻力与动力消耗；传热面积与投资的定量关系。为正确选用不同结构金属换热器及其性能提供了依据。