镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Al-Zn-Ce非晶合金的相选择与组织结构演化

本文研究了具有典型分解特征的Al-Zn-Ce非晶合金的形成和晶化过程，探讨了各种相的生成顺序。XRD和DSC测试结果表明强烈的化合物短程序有利于Al-Zn-Ce非晶合金的形成。在Al-Zn-Ce非晶合金的晶化过程中存在复杂的相选择行为，多种相的竞争形核和有限生长使其具有复杂的结构特点。同时，结果也表明冷速对该体系非晶的形成有很大影响。     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.     

Failure analysis of a hot extrusion die used for Al-Li alloy processing

Al-Li alloys being developed as lighter, substitutes for conventional high strength Al alloys are to be processed by routine methods. During extrusion of a 8090 Al-Li alloy, the extrusion die container failed causing some alarm. This failed die container was analysed to examine if the failure was caused by interaction of Li diffusing out of Al-Li alloy with the carbides of die steel. The evidence, although not conclusive, is sufficient to exercise caution during such processing.     

机械合金化Fe50Ti50非晶的形成及球磨强度对它的影响

本文通过电子扫描和Ｘ衍射对机械合金人Ｆｅ５０Ｔｉ５０非晶粉末形成做了研究。研究发现：机械合金非晶形成可以大致地分为二个阶段－粉末的破碎阶段和非晶的形成阶段。另外，对球磨强度对非晶形成的影响进行了研究。结果表明：强度低时粉末需要较长的时间才能形成非晶，强度高时粉末形成非晶的时间大大缩短，但在随后的球磨中，粉末会重新晶化形成新相。     

A numerical model for the dissolution of spherical particles in binary alloys under mixed mode control

A general numerical model is described for the dissolution kinetics of spherical particles in binary systems for any combination of first order reactions at the particle-matrix interface and long distance diffusion within the matrix. The model is applicable to both finite and infinite media and handles both complete and partial particle dissolution. It is shown that interfacial reactions can have a strong effect on the dissolution kinetics, the solute concentration at the particle-matrix interface and the solute concentration profile in the matrix.     

Peculiarities of erosion-corrosion processes

Investigations have been carried out on an erosion-corrosion apparatus to investigate the behaviour of corrosion-resistant highalloy iron-base materials containing hard phases. These materials had been optimized for increased wear resistance under complex stress conditions. As expected, in dry erosion tests, very low mass losses were established; there was little difference between the materials. Also, in corrosive environments (NaCl, H₂SO₄), the materials showed good stability; however, the duplex structures were superior to the martensitic ones. The combination of erosion and corrosion produced large differences and, in some cases, markedly reduced resistance to damage. These results confirmed observations that it is impossible to deduce the environmentally influenced mechanical behaviour of an alloy from its behaviour in separate corrosion and erosion experiments. The basic mechanisms underlying these processes have been investigated only tentatively.     

激光结晶a-Si:H SOI离子注入和快速退火

本文对激光结晶a-Si∶H SOI结构砷注入和快速退火行为作了研究.a-Si∶H激光结晶有Lp-LCR,OD,FCR-2,FCR-1四个结晶区.用剖面电镜观察了结晶区的结构.扩展电阻测量表明Lp-LCR区中有两种扩散机制,即杂质在晶粒体内扩散和沿缺陷扩散.OD区中有三种扩散形式,除有上述两种以外,还有沿缺陷的扩散.首次比较了沿晶界和缺陷的扩散速度.