Application of degradation kinetics to the rheology of poly(hydroxyalkanoates)

The time‐dependent rheological behavior of a series of 3‐hydroxybuytrate‐based semicrystalline copolymers is employed to determine the expected rheological curves that would be generated in the absence of any polymer degradation. Both dynamic frequency sweep and shear rate sweep experiments were analyzed. A model for the degradation kinetics, coupled with standard rheological relationships, was employed to extrapolate the measured sweeps to predicted curves at time zero, prior to degradation. The model is broadly applicable over a wide range of frequencies or shear rates, and generates a single degradation rate constant k for each polymer studied. A similar, although ad hoc, procedure was applied to the dynamic storage and loss moduli. The model provides a method for determining the rheological behavior of degrading polymers over a time interval, typically found in processing applications. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1794–1802, 2006     

共轭高分子三阶非线性光学材料

概述了ｎ－共轭高分子材料的三阶非线性光学性质，着重讨论了化学结构对其光学非线性的影响，说明了ｎ－共轭聚合物的三阶非线性极化率主要取决于共轭主链的结构，侧链取代基的变化对其非线性影响不大，文中展望了共轭高分子材料在集成光学中的应用前景。     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

Red emission from Eu3+: PVA polymer film

Bright red luminescent Eu³⁺ doped polyvinyl alcohol (PVA) films were made by solution casting technique. The emission performance of these films was studied from the measurement of excitation, emission, and lifetimes. On irradiation with an UV source, the doped films emitted bright red light. Such luminescent polymer films are expected to find potential applications as new optical materials. Emission process in the system was explained by an energy level scheme. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3273–3276, 2006     

Improvement of device performances by thin interlayer in conjugated polymers/methanofullerene plastic solar cell

Recent studies have reported that a thin interlayer between poly(3, 4-ethylene dioxythiophene)-poly(styrene sulfonic acid) (PEDOT: PSS) and an emissive polymer layer leads to a large increase in the performances of polymer light-emitting diodes (PLEDs) by preventing significant quenching of the radiative excitons at the PEDOT: PSS interface; therefore, acting as an efficient exciton-blocking layer. Using the similar idea, a thin interlayer was fabricated between PEDOT: PSS and the active layer of conjugated polymers/methanofullerene composites in a plastic solar cell. The interlayer consisted of a poly(fluorene)-based hole transporter spin-coated directly on top of the PEDOT: PSS layer. The devices with the interlayer exhibited a higher efficiency than in those without the interlayer.     

Sidechain liquid crystal polymers

Research has continued in the field sidechain liquid crystal polymers over recent years, but it is becoming clearer that this research is being directed away from the traditional technology areas of electro-optic devices and researchers are developing new and exciting applications for this novel state of matter.     

Electrochemical,FTIR and morphological study of polypyrrole—Polystyrenesulphonate conducting films

The electrochemical behaviour, FTIR spectrum and the morphology of polypyrrole-polystyrenesulphonate (PPy-PSS) films obtained potentiostatically at 0.6 V in a 0.05m Py + 1.7 × 10^?2m NaPSS medium have been analysed. Different electrochemical parameters have been modified in order to establish the first polaron formation, the reversibility of the redox process and the doping mechanism. The FTIR spectrum confirms the existence of C?O groups in the film structure and two possible explanations are suggested. SEM reveals a higher homogeneity in these films than in PPy films doped with smaller counterions.     

Carbon fibre composites based on polyimide/silica ceramers: aspects of structure-properties relationship

Polyimide/silica ceramers, based on the products of the hydrolysis of tetraethoxysilane (TEOS) and a commercial poly(amic acid) solution, were used to fabricate unidirectional carbon fibre composites, which were subsequently evaluated with respect to thermal and mechanical properties. There is evidence to suggest that the silica component of these ceramers is present as dispersed discrete particles at low silica concentration (i.e. 7 wt%) and as fine interconnected domains trapped within the polyimide matrix at higher silica content (i.e. 14 wt%). The dimensions of the silica domains were in the region of 7–20 nm. Carbon fibre composites produced from ceramer solutions (CF/ceramers) were found to exhibit lower thermal expansion and a greater retention of flexural and interlaminar shear properties at elevated temperature than the corresponding polyimide-matrix composites (CF/polyimide). The properties of CF/ceramers were generally better for systems containing the higher amount of silica and were improved further by lowering the pH value of the precursor ceramer solution. This is believed to have resulted from the enhanced fluidity of the ceramer gel within the pre-impregnated fibres, giving rise to a higher packing density of the fibres and a more homogeneous distribution of fibres. CF/ceramers were also found to exhibit a better thermal oxidative stability at 350°C than the corresponding CF/polyimide, although a substantial amount of porosity developed in the case of ceramers with the higher silica content.     

UV-laser assisted Fabrication of integrated-optical Waveguides

By UV-laser-irradiation a controllable change of the refractive index of some polymers can be attained in the irradiated zone. The detailed UV-photon-induced process mechanisms have been investigated on the basis of PMMA employed as an UV-modifiable model polymer. By mask lithographic methods the UV-laser-assisted technology for the modification of the polymer optical properties enables the local increase of the refractive index and thus the fabrication of integrated-optical waveguiding elements in the surface of a planar polymer chip. These elements are relevant for the manufacturing of complex integrated-optical components. The optical and functional properties of the integrated-optical waveguides have been characterized.     

Room-Temperature Solid-State Lithium Metal Batteries Using Metal Organic Framework Composited Comb-Like Methoxy Poly(ethylene glycol) Acrylate Solid Polymer Electrolytes

Solid polymer electrolyte with good thermal stability and flexibility is an excellent candidate for solid-state lithium metal batteries, while its low ionic conductivity caused by high crystallinity limits its application at ambient temperature. Here a metal organic framework (zeolitic imidazolate framework-8, ZIF-8) composited comb-like methoxy poly(ethylene glycol) acrylate polymer electrolyte (MCPE) with high ionic conductivity (9.96 × 10⁻⁵ S cm⁻¹ at 30 °C) is prepared by an in situ UV polymerization method. The as-prepared MCPE exhibits improved mechanical property due to the introduction of porous ZIF-8 nanofillers, which is beneficial to suppress the growth of lithium dendrites. Consequently, the LiFePO₄||MCPE||Li cells show a high capacity of 116 mAh g⁻¹ at 30 °C and 0.5 C, and maintain 89.4% of initial capacity after 150 cycles with the average Coulombic efficiency of 99.9%. These results demonstrate that the MCPE shows great potential in solid-state lithium metal batteries near room temperature.