陶瓷材料的冷加工与热处理

综述评述最近发展起来的陶瓷材料的烧结后冷加工热处理法“控制破碎成形加工法”，着重介绍该方法的由业，阐明其理论与实验基础，同时，介绍其应用并讨论其发展前景。     

�Ľ�ģ���˻��㷨��ˮ����������ƽ������е�Ӧ��

Kirkpatrick于1982年认识到固体粒子退火过程和组合优化问题有相似性，从而提出了模拟退火算法，并从数学上已证明了模拟退火算法可以取得全局最优解。相比之下，传统的最优化法只能求局部最优值。在计算物质平衡方程时，存在很多不确定的参数，给精确计算带来了一定困难。因此，本文引入模拟退火算法求解物质平衡方程。     

SiGe: An attractive material for post-CMOS processing of MEMS

This work gives an overview of the different developments for silicon germanium (Si_1−xGe_x) from a MEMS post-processing perspective. First, the maximum processing temperature that does not introduce any damage or degradation into the standard characteristics of the CMOS driving electronics is specified. Then, the optimal type of silicon and germanium gas sources and deposition technique that results in an economical process are identified. Next, the selection criteria for a low thermal budget doping method and doping species are discussed. Finally, the advantage and disadvantage for the different approaches implemented for enhancing the physical properties of poly Si_1−xGe_x at a CMOS backend compatible temperature are highlighted. It is shown that the optimal method depends on the application requirements and the CMOS technology used for realizing the driving electronics.     

Radiation effects on insulators for superconducting fusion magnets

Fibre-reinforced plastics (FRPs) are candidate materials for the insulation of superconducting magnet coils in future fusion reactors. This paper reports on a test programme performed to assess the mechanical properties of these materials and to obtain information on the damage and fracture mechanisms. Different types of FRPs (epoxies and poly- and bismaleimides as resins; two- and three-dimensional E-, S- or T-glass fabrics as reinforcements) were irradiated at room temperature by 2 MeV electrons and ⁶⁰Co-gamma rays up to 1.8 × 10⁸ Gy and by different reactor spectra up to a neutron fluence of 1 × 10²³ m⁻² (E > 0.1 MeV) at room temperature, 80 K or 5 K. Mechanical tests in tension as well as in the intralaminar crack opening and shear mode were carried out on the irradiated samples at 77 K. After low temperature irradiation, half of the samples were subjected to a warm-up cycle to room temperature before testing at 77 K. Results on the influence of different radiation sources and annealing cycles on the mechanical properties of these materials will be discussed.     

碳/环氧复合材料的冲击拉伸

该文研究了T300碳纤维单向增强的环氧复合材料,在应变率从10~(-3)/s到10~3/s范围内的冲击拉伸行为.通过对实验数据进行拟合,得出该范围内材料对应变率具有弱的敏感性,表现在破坏强度及破坏应变随应变率增加不显著变化,平均模量几乎不受应变率的影响.分析了试件的几何尺寸效应,讨论了应力波作用对破坏形态的影响以及实验中观察到的拔出现象.从应变率在10~2～10~3/s附近材料行为某些非确定性,指出在更宽范围内了解其性能的必要性.     

离子注入硅的线源非相干光瞬时退火温度计算

本文利用高温模型,计算了在我们的实验条件下对离子注入硅进行线源非相干光瞬时退火的退火温度,并与实验结果比较,两者符合得较好。     

具有多重焦点的波带透镜的设计

本文提出了一种新型的具有多重焦点的波带透镜的概念及其设计方法。可提供某些特定的光场分布,而且具有性能稳定、微型化和可实际制作等特点。     

Sparse synthetic aperture radar imaging with optimized azimuthal aperture

To counter the problem of acquiring and processing huge amounts of data for synthetic aperture radar(SAR)using traditional sampling techniques,a method for sparse SAR imaging with an optimized azimuthal aperture is presented.The equivalence of an azimuthal match filter and synthetic array beamforming is shown so that optimization of the azimuthal sparse aperture can be converted to optimization of synthetic array beamforming.The azimuthal sparse aperture,which is composed of a middle aperture and symmetrical bilateral apertures,can be obtained by optimization algorithms(density weighting and simulated annealing algorithms,respectively).Furthermore,sparse imaging of spectrum analysis SAR based on the optimized sparse aperture is achieved by padding zeros at null samplings and using a non-uniform Taylor window.Compared with traditional sampling,this method has the advantages of reducing the amount of sampling and alleviating the computational burden with acceptable image quality.Unlike periodic sparse sampling,the proposed method exhibits no image ghosts.The results obtained from airborne measurements demonstrate the effectiveness and superiority of the proposed method.     

考虑疫情扩散传播风险的多目标拼车应急管理优化调度模型

为了解决在疫情背景下传统拼车出行模式面临的交互传染风险,对疫情背景下的拼车管理进行分析,提出了将低风险及潜在风险乘客分开服务的拼车策略。在进一步考虑拼车系统应兼顾的社会效益及服务质量的基础上,构建了在满足基本额定盈利及最小化等待时长的双目标拼车应急管理优化调度模型,并给出了求解该模型的组合模拟退火算法。通过具体算例对模型的有效性进行验证,结果表明模型能够较快收敛到一个稳定值,且计算结果能够反映实际场景,说明了模型及算法的有效性。最后,通过一个仿真实验对所构建模型在病毒传播中的作用进行了分析,结果显示所构建的模型可以有效抑制拼车导致的病毒传播速度。     

短波chirp探测的遗传退火频率分配算法研究

针对短波chirp探测系统的通信网络频率分配问题,建立了合理的干扰模型;利用系统所提供的测量参数,结合基本遗传算法,同时进行模拟退火操作以克服基本遗传算法易陷入局部最优解的不足,并最终趋于全局最优化;仿真结果表明,该算法在寻优性、收敛速度和稳定性等方面都要优于基本遗传算法。