A generalized analysis for cascading single fluid vapor compression refrigeration cycles using an entropy generation minimization method

This paper focuses on cascading an ideal vapor compression cycle and determining the optimal intermediate temperatures based on the entropy generation minimization method. Only superheating and throttle losses of the cycle are considered since they are inherent to the ideal vapor compression refrigeration cycle. The second law equations have been developed in terms of specific heats and temperature ratios with the intent of reducing involved property modeling. Also the entropy generation was expressed in terms of a single independent variable and minimized to develop an advanced rule for selecting optimum intermediate temperatures. Results for a cascade system operating between reduced temperatures of 0.684 and 0.981 with R-134a as the working fluid are presented. The approximate method presented here predicted the optimum intermediate reduced temperature for a two-stage system to be 0.88, a difference of 2% from the optimum. The method presented was a much better predictor of the optimum temperature than the geometric mean method which was 0.82, a difference of 5% from the optimum. The entropy generation distribution of the optimum solution was investigated. For a two-stage system, the lower stage and higher stage entropy generation was 44% and 56%, respectively. In comparison to the single stage, the two-stage reduced losses by 78%.     

平遥县尹回水库工程存在问题及处理措施

文中根据尹回水库工程存在问题，分析了水库工程除险加固改造的必要性，提出了水库除险加固工程措施。     

Refrigeration and the world's food supply — especially in developing countries

The reason for starvation today is poverty. Refrigeration can help the developing countries to export high value products. This helps to improve the economical situation and their buying power. Refrigeration can also help to reduce waste. Primitive distribution systems using refrigeration can be used at an early stage but the infrastructure is the limiting factor for introduction of modern transport equipment. Appropriate refrigeration technology is required, and the IIR should promote this by, for example, introducing an award for good proposals.     

Heritage values and functions of wetlands in Southern Mexico

There is a wealth of heritage values and contemporary functions of freshwater and estuarine wetlands along the coast of the Yucatan Peninsula in Mexico and northern Belize. These vary from ancient Maya use for multicropping and aquaculture to current use for fishing, hunting, freshwater supplies, salt extraction and nature tourism. Potential conflicts and collaborations will be discussed with reference to proposed restoration of ancient Maya water management systems combined with modern technologies. Particular attention will be paid to wetland use, which combines both traditional and “new” uses including partial restoration, agro-ecology and ecotourism.     

Influence of cryogenic temperatures on food products and packaging during rail transport

Six commercially packaged frozen food products were subjected to simulated railway shock and vibration conditions and manual handling abuse at both cryogenic (−70°C) and non-cryogenic (−18°C) temperatures. The amount of package and food product damage under different temperatures and levels of abuse were determined. The effects of cryogenic temperatures upon sensory and various analytical quality attributes of the food products were examined. The test results indicated that frozen food can be shipped at cryogenic temperatures in railcars equipped with cushioned draft gears with minimal product or packaging damage, provided there is not excessive manhandling abuse.     

Evaluation of corrosion resistance of two engineering alloys in molten salts by electrochemical techniques

The electrochemical behaviour of two steels typically used in power boilers has been studied in the temperature range from 540°C to 680°C. Two environments were used: a) a synthetic salt mixture of 80% V₂O₅ ? 20% Na₂SO₄ and b) oil ash collected from a high temperature reheater. Corrosion rates obtained from electrochemical potentiodynamic polarisation curves (Tafel extrapolation) were compared for both steels exposed in each environment. The results showed that increases in temperature resulted in higher corrosion rates, being this effect most notorious above about 620°C. In the synthetic salt, and at temperatures up to about 580°C, both steels showed similar behaviour. With further increases in temperature, the T22 steel was less resistant and, at the highest temperature used here, its corrosion rate was almost seven times higher than that measured for the 347H steel. The results obtained with the natural oil ash for the T22 steel showed a dramatic increase in corrosion rate as temperature goes up over the range used. For the 347H steel, and up to about 580°C, the corrosion rates were similar to those obtained with the synthetic salt. Above 580°C, the corrosion rate measured increased slightly with temperature, being at 680°C about 2.5 times higher than that found by using the synthetic salt. Therefore, an important difference in corrosion rates has been found depending upon the corrosive salt used. This is an important result because imply that, at least for materials used in fossil power plants, more realistic data can be obtained by using natural ashes in the experimental work.     

由三氯戊烯酮合成吡唑类化合物的研究(Ⅰ)

１，１，５－三氯－１－戊烯－３－酮（１）是一种杂环合成的活泼中间体。本研究选用有一定代表性的肼类试剂，研究了它们与１反应的成环条件。由１与芳肼反应合成了６种化合物（２～７），除７外都是新化合物。所有新化合物的结构经ＩＲ、ＭＳ、元素分析等手段证实。所合成化合物结构如下：     

Mathematical model of critical implant stress testing in the weld metal of API 5L X80 steel

In this paper the influence of heat input and preheat temperature on the critical implant stress was analyzed for the weld metal of API 5L X80. High strength steel marked as API 5L X80 is produced with a thermo – mechanical controlled process (TMCP), its chemical composition shows low carbon content due to which the steel has good weldability, but in the weld metal zone cold cracking can occure. The goal of this paper is to define optimal work conditions in form of flux cored arc welding (FCAW) welding parameters at which no cold cracks can be found. The experiment was conducted using central composite design (CCD) and design of experiments (DoE) with two independent variables (preheat temperature and heat input). Mathematical models were developed for all three different wire types that were used (two rutile, one basic flux cored wire). The samples in this paper which had cold cracks were further analyzed on the scanning electron microscope (SEM).